Autodesk® Inventor CAM™ 2024

Release Notes

Build 11.0.0.21457 / 12 April 2023 Autodesk, Inc.

This document covers these Inventor CAM products:

Inventor CAM Premium
Inventor CAM Ultimate

What’s New
System Requirements
Installation

WHAT’S NEW

The following changes have been made in the current update (2024):

Changes for 2D Contour

Fixed possible linking issues in Contour2D when input contours contain arcs with the same center. (#41769)
Fixed a bug when "finishing feedrate" might not apply to last finishing path. (#41670)
Fixed a case when Contour2D could fail to generate toolpath for narrow slots with ramp linking. (#41497)

Changes for Blend & Flow

Fixed an issue in Flow operations where the toolpath might not be machined if the tilt angle was exceeded on a machine with limited axial motion. (#39642)
Added damping for toolaxis limits in Blend and Flow with a non ball tool. When the toolaxis hits the limit, it will decelerate to a stop rather than stopping suddenly. (#40955)
Fixed a possible holder gouge in Blend and Flow strategies with enabled "Trim" option in holder protection. (#42254)
Fixed a failed toolpath calculation in Blend which occured in some instances where machining boundaries were used. (#41413)
Fixed possible small gouges in Blend, Flow and Multi-axis contour. (#40975)
Added Blend toolpath joining in more cases if the endpoints are aligned. This gives fewer and more uniform linking paths. (#39983)
Fixed a bug which could result in an empty or incomplete toolpath for Flow. Fixed an issue related to duplicated paths in Flow. (#41394)
Fixed a case where Flow (Preview) could fail to calculate a toolpath with an unexpected error. (#40710)
Fixed trimmed toopath in undercut areas in Flow with enabled collison avoidance. (#40419)
Made improvements so that operations like Flow produces less gouging toolpaths. (#40388)
Fixed possible crashes in Blend (#40630, #40507)

Changes for Milling (Other Strategies)

Fixed an issue in which 2D Pocket could gouge the part when using Smooth Profile Ramp in some cases with very small arcs. (#42294)
Fixed an issue in which the wrong stock to leave was computed against "avoid surfaces". (#40513)
Fixed a possible issue with sub-sampling in Engrave so the toolpath will stay more than tolerance away from selected input curves. (#41035)
Improved the performance for Pocket3D. (#38796)
Fixed a case where an operation with the combination of selected machining boundaries and adding fillets could fail to generate a toolpath. (#40731)
Fixed an issue by preventing ConstScallop from going below Zlow when offsetFromAreas is being used. (#32387)
Fixed a possible crash in Spiral with enabled morph option when zero area boundaries are selected. (#36484)
Fixed possible crashes in Swarf (#37618, #35718), Trace (#38297), Scallop (#40956), Wrap (#41141), and others. (#41886)

Changes for Turning

Fixed an issue with certain turning grooving operations where the tool was not going down to the depth set by the inner radius. (#41284)

Changes for User Interface

Fixed an issue which could cause a crash in some cases when changing the vector direction in Selection. (#38514)
Fixed an issue in which the Select button could be overlapped by other visual elements. (#43143)
Fixed a translation issue on the "About" page. (#41376)
Fixed a problem in operation dialogs where the text of an edit box was not being selected when tabbing into it. (#41820)

Return to Top

SYSTEM REQUIREMENTS

Autodesk Inventor CAM 2024 supports Microsoft Windows 10 64-bit and Windows 11 64-bit.
Inventor CAM 2024 is compatible with the 2022, 2023 and 2024 versions of Inventor and Inventor Professional.

Return to Top

INSTALLATION

New installation

Inventor must be installed prior to installing Inventor CAM
If you need to install Inventor, it should be available to you in the Autodesk Account Portal
Before you install Inventor CAM 2024, please make sure to run Windows Update, install all Windows Updates that are pending on your machine, and reboot:
- For Windows 10: Windows Update is available in the Update and Security section of Windows Settings, which is available from the Windows menu.
It is sometimes necessary to perform a Windows Update multiple times to completely update your operating system.
Verify that enough disk space is available on your machine to install Inventor CAM 2024.
Before installing Inventor CAM 2024, please uninstall all prior Autodesk beta products.
Download Inventor CAM 2024 from the Autodesk Account Portal or from your Autodesk Desktop Application.
Follow the instructions to download and launch the installer. Temporary extraction is to your temp folder. Operating system errors regarding very long path names can occur if the temporary location is nested too many levels deep.
If the installer does not launch, browse to the folder where the files were extracted, and double-click setup.exe.

Updating an existing installation

When a new update is available, an update notification will appear in the Autodesk Desktop App.
Please download and install the update package.

Before installing an update there is no need to uninstall a previous Inventor CAM release; but if you prefer to do so, you can uninstall the relevant release in Programs and Features in Windows Control Panel by accessing “View installed updates”.

Return to Top

FEEDBACK

We encourage you to provide your feedback to us and help make Inventor CAM even better. If you encounter issues not covered in this document, please report them to Autodesk through your reseller, on the CAM discussion forum, or to the Inventor CAM team using 'Send Feedback' on the 'Help' menu.

The Autodesk CAM Team
For more information visit us at: http://cam.autodesk.com