/**
Copyright (C) 2012-2024 by Autodesk, Inc.
All rights reserved.
HAAS VR-8 post processor configuration.
$Revision: 44134 ad59f0c8ce196c55a2d8008954e7c105e1b18c4e $
$Date: 2024-07-10 03:53:32 $
FORKID {DBD402DA-DE90-4634-A6A3-0AE5CC97DEC7}
*/
description = "Haas VR-8";
var homePositionX = "-46in"; // X-home position in inches
var homePositionY = "0in"; // Y-home position in inches
var adjustRetractHeight = true; // adjust retract height for A-axis position to avoid tool changer
highFeedrate = 500 * 25.4; // must be in MM
// >>>>> INCLUDED FROM haas/head-head/common/haas head-head.cps
///////////////////////////////////////////////////////////////////////////////
// MANUAL NC COMMANDS
//
// The following ACTION commands are supported by this post.
//
// bDirection: positive, closest, negative - Selects the preferred direction of the B-axis
// VFD_HIGH - Uses high pressure flood coolant if machine has VFD
// VFD_LOW - Uses low pressure flood coolant if machine has VFD
// VFD_NORMAL - Uses normal pressure flood coolant if machine has VFD
//
///////////////////////////////////////////////////////////////////////////////
if (!description) {
description = "Haas Head-Head Mill";
}
vendor = "Haas Automation";
vendorUrl = "https://www.haascnc.com";
legal = "Copyright (C) 2012-2024 by Autodesk, Inc.";
certificationLevel = 2;
minimumRevision = 45909;
longDescription = subst("Generic post for the %1 mill with a Next Generation control.", description);
extension = "nc";
programNameIsInteger = true;
setCodePage("ascii");
capabilities = CAPABILITY_MILLING | CAPABILITY_MACHINE_SIMULATION;
tolerance = spatial(0.002, MM);
minimumChordLength = spatial(0.25, MM);
minimumCircularRadius = spatial(0.01, MM);
maximumCircularRadius = spatial(1000, MM);
minimumCircularSweep = toRad(0.01);
maximumCircularSweep = toRad(355);
allowHelicalMoves = true;
allowedCircularPlanes = undefined; // allow any circular motion
allowSpiralMoves = true;
allowFeedPerRevolutionDrilling = true;
probeMultipleFeatures = true;
// user-defined properties
properties = {
writeMachine: {
title : "Write machine",
description: "Output the machine settings in the header of the code.",
group : "formats",
type : "boolean",
value : false,
scope : "post"
},
writeTools: {
title : "Write tool list",
description: "Output a tool list in the header of the code.",
group : "formats",
type : "boolean",
value : true,
scope : "post"
},
writeVersion: {
title : "Write version",
description: "Write the version number in the header of the code.",
group : "formats",
type : "boolean",
value : false,
scope : "post"
},
preloadTool: {
title : "Preload tool",
description: "Preloads the next tool at a tool change (if any).",
group : "preferences",
type : "boolean",
value : true,
scope : "post"
},
showSequenceNumbers: {
title : "Use sequence numbers",
description: "'Yes' outputs sequence numbers on each block, 'Only on tool change' outputs sequence numbers on tool change blocks only, and 'No' disables the output of sequence numbers.",
group : "formats",
type : "enum",
values : [
{title:"Yes", id:"true"},
{title:"No", id:"false"},
{title:"Only on tool change", id:"toolChange"}
],
value: "true",
scope: "post"
},
sequenceNumberStart: {
title : "Start sequence number",
description: "The number at which to start the sequence numbers.",
group : "formats",
type : "integer",
value : 10,
scope : "post"
},
sequenceNumberIncrement: {
title : "Sequence number increment",
description: "The amount by which the sequence number is incremented by in each block.",
group : "formats",
type : "integer",
value : 5,
scope : "post"
},
optionalStop: {
title : "Optional stop",
description: "Specifies that optional stops M1 should be output at tool changes.",
group : "preferences",
type : "boolean",
value : true,
scope : "post"
},
separateWordsWithSpace: {
title : "Separate words with space",
description: "Adds spaces between words if 'yes' is selected.",
group : "formats",
type : "boolean",
value : true,
scope : "post"
},
useRadius: {
title : "Radius arcs",
description: "If yes is selected, arcs are output using radius values rather than IJK.",
group : "preferences",
type : "boolean",
value : false,
scope : "post"
},
useParametricFeed: {
title : "Parametric feed",
description: "Parametric feed values based on movement type are output.",
group : "preferences",
type : "boolean",
value : false,
scope : "post"
},
showNotes: {
title : "Show notes",
description: "Enable to output notes for operations.",
group : "formats",
type : "boolean",
value : false,
scope : "post"
},
useG0: {
title : "Use G0",
description: "Specifies that G0s should be used for rapid moves. Make sure that Setting 335 (LINEAR RAPID MOVE) is set to 'Linear + Rotary'.",
group : "preferences",
type : "boolean",
value : false,
scope : "post"
},
useG28: {
title : "Use G28 instead of G53",
description: "Specifies that machine retracts should be done using G28 instead of G53.",
group : "homePositions",
type : "boolean",
value : false,
scope : "post"
},
useSubroutines: {
title : "Use subroutines",
description: "Select your desired subroutine option. 'All Operations' creates subroutines per each operation.",
group : "preferences",
type : "enum",
values : [
{title:"No", id:"none"},
{title:"All Operations", id:"allOperations"},
{title:"Cycles", id:"cycles"},
{title:"Patterns", id:"patterns"}
],
value: "none",
scope: "post"
},
useSmoothing: {
title : "Use G187",
description: "G187 smoothing mode.",
group : "preferences",
type : "enum",
values : [
{title:"Off", id:"-1"},
{title:"Automatic", id:"9999"},
{title:"Rough", id:"1"},
{title:"Medium", id:"2"},
{title:"Finish", id:"3"}
],
value: "-1",
scope: "post"
},
optionallyCycleToolsAtStart: {
title : "Optionally cycle tools at start",
description: "Cycle through each tool used at the beginning of the program when block delete is turned off.",
group : "preferences",
type : "boolean",
value : false,
scope : "post"
},
measureTools: {
title : "Optionally measure tools at start",
description: "Measure each tool used at the beginning of the program when block delete is turned off.",
group : "preferences",
type : "boolean",
value : false,
scope : "post"
},
toolBreakageTolerance: {
title : "Tool breakage tolerance",
description: "Specifies the tolerance for which tool break detection will raise an alarm.",
group : "preferences",
type : "spatial",
value : 0.1,
scope : "post"
},
safeStartAllOperations: {
title : "Safe start all operations",
description: "Write optional blocks at the beginning of all operations that include all commands to start program.",
group : "preferences",
type : "boolean",
value : false,
scope : "post"
},
fastToolChange: {
title : "Fast tool change",
description: "Skip spindle off, coolant off, and Z retract to make tool change quicker.",
group : "preferences",
type : "boolean",
value : false,
scope : "post"
},
useG95forTapping: {
title : "Use G95 for tapping",
description: "use IPR/MPR instead of IPM/MPM for tapping",
group : "preferences",
type : "boolean",
value : false,
scope : "post"
},
safeRetractDistance: {
title : "Safe retract distance for rewinds",
description: "Specifies the distance to add to retract distance when rewinding rotary axes.",
group : "multiAxis",
type : "string",
value : "0in",
scope : "post",
kind : "spatial"
},
safeRetractDistanceZ: {
title : "Safe Z-retract distance for head rotations",
description: "Specifies the distance above the part to retract to when positioning rotary axes on a head machine.",
group : "multiAxis",
type : "string",
value : "4in",
scope : "post",
kind : "spatial"
},
useMultiAxisFeatures: {
title : "Use FCS",
description: "Specifies that the Feature Coordinate System (G268/G269) should be used.",
group : "multiAxis",
type : "boolean",
value : true,
scope : "post"
},
preferredTilt: {
title : "Preferred B-axis direction",
description: "Select the desired direction for the B-axis.",
group : "multiAxis",
type : "enum",
values : [
{title:"Positive", id:"1"},
{title:"Closest", id:"0"},
{title:"Negative", id:"-1"}
],
value: "0",
scope: "post"
},
homePositionX: {
title : "G53 home position X",
description: "G53 X-axis home position used as safe tool change position.",
group : "homePositions",
type : "string",
value : homePositionX,
scope : "post",
kind : "spatial"
},
homePositionY: {
title : "G53 home position Y",
description: "G53 Y-axis home position used as safe tool change position.",
group : "homePositions",
type : "string",
value : homePositionY,
scope : "post",
kind : "spatial"
},
homePositionZ: {
title : "G53 home position Z",
description: "G53 Z-axis home position.",
group : "homePositions",
type : "string",
value : "0in",
scope : "post",
kind : "spatial"
},
forceHomeOnIndexing: {
title : "Move to home prior to head alignment",
description: "Enable to move to the defined G53 home position in X & Y prior to a head alignment move.",
group : "homePositions",
type : "boolean",
value : false,
scope : "post"
},
centerOnMultiAxis: {
title : "Move to center of model for head positioning",
description: "Enable to move to the center of the model prior to rotating the heads in a multi-axis operation.\nUsed to avoid exceeding the XY-limits of the machine.",
group : "homePositions",
type : "boolean",
value : false,
scope : "post"
},
adjustKnuckleAngle: {
title : "Automatic C-axis positioning",
description: "Choose the automatic positioning of C-axis based on the direction of a 3-axis cut.\nDisabled - disables automatic positioning, \nPreposition - prepositions the C-axis prior to each move, \nStay down - repositions the C-axis prior to the move when the limit is reached, \nRetract - retracts and repositions the C-axis when the limit is reached, \nLock - locks the C-axis at the current angle when the limit is reached, ",
type : "enum",
group : "multiAxis",
values : [
{title:"Disabled", id:"disabled"},
{title:"Preposition", id:"preposition"},
{title:"Stay down", id:"staydown"},
{title:"Retract", id:"retract"},
{title:"Lock", id:"lock"}
],
value: "disabled",
scope: "post"
},
knuckleCircular: {
title : "Circular C-axis positioning",
description: "Choose the output style for automatic positioning of the C-axis on circular blocks.\nYes - outputs the C-axis on a circular block, \nNo - linearizes circular moves when Automatic C-axis positioning is enabled, \nLock - locks the C-axis at the current angle for circular blocks, \n",
type : "enum",
group : "multiAxis",
values : [
{title:"Yes", id:"true"},
{title:"No", id:"false"},
{title:"Lock", id:"lock"}
],
value: "true",
scope: "post"
},
baseKnuckleAngle: {
title : "Base C-axis positioning angle",
description: "Defines the direction of the C-axis for a move along the postive X-axis in degrees.",
group : "multiAxis",
type : "number",
value : 90,
scope : "post"
},
singleResultsFile: {
title : "Create single results file",
description: "Set to false if you want to store the measurement results for each probe / inspection toolpath in a separate file",
group : "probing",
type : "boolean",
value : true,
scope : "post"
},
useClampCodes: {
title : "Use clamp codes",
description: "Specifies whether clamp codes for rotary axes should be output. For simultaneous toolpaths rotary axes will always get unclamped.",
group : "multiAxis",
type : "boolean",
value : true,
scope : "post"
},
coolantPressure: {
title : "Coolant pressure",
description: "Select the coolant pressure if equipped with a Variable Frequency Drive. Select 'Default' if this option is not installed.",
group : "preferences",
type : "enum",
values : [
{title:"Default", id:""},
{title:"Low", id:"P0"},
{title:"Normal", id:"P1"},
{title:"High", id:"P2"}
],
value: "",
scope: "post"
},
usePeckTapping: {
title : "Use Peck for tapping",
description: "Software version 100.23.000.1201 now supports Q-peck parameter for peck tapping cycles.",
group : "preferences",
type : "boolean",
value : false,
scope : "post"
}
};
// wcs definiton
wcsDefinitions = {
useZeroOffset: false,
wcs : [
{name:"Standard", format:"G", range:[54, 59]},
{name:"Extended", format:"G154 P", range:[1, 99]}
]
};
var singleLineCoolant = false; // specifies to output multiple coolant codes in one line rather than in separate lines
// samples:
// {id: COOLANT_THROUGH_TOOL, on: 88, off: 89}
// {id: COOLANT_THROUGH_TOOL, on: [8, 88], off: [9, 89]}
// {id: COOLANT_THROUGH_TOOL, on: "M88 P3 (myComment)", off: "M89"}
var coolants = [
{id:COOLANT_FLOOD, on:8},
{id:COOLANT_MIST},
{id:COOLANT_THROUGH_TOOL, on:88, off:89},
{id:COOLANT_AIR, on:83, off:84},
{id:COOLANT_AIR_THROUGH_TOOL, on:73, off:74},
{id:COOLANT_SUCTION},
{id:COOLANT_FLOOD_MIST},
{id:COOLANT_FLOOD_THROUGH_TOOL, on:[88, 8], off:[89, 9]},
{id:COOLANT_OFF, off:9}
];
// old machines only support 4 digits
var oFormat = createFormat({width:5, zeropad:true, decimals:0});
var nFormat = createFormat({decimals:0});
var gFormat = createFormat({prefix:"G", decimals:0});
var mFormat = createFormat({prefix:"M", decimals:0});
var hFormat = createFormat({prefix:"H", decimals:0});
var dFormat = createFormat({prefix:"D", decimals:0});
var probeWCSFormat = createFormat({prefix:"S", decimals:0, forceDecimal:true});
var probeExtWCSFormat = createFormat({prefix:"S154.", width:2, zeropad:true, decimals:0});
var xyzFormat = createFormat({decimals:(unit == MM ? 3 : 4), forceDecimal:true});
var rFormat = xyzFormat; // radius
var abcFormat = createFormat({decimals:3, forceDecimal:true, scale:DEG});
var feedFormat = createFormat({decimals:(unit == MM ? 2 : 3), forceDecimal:true});
var feedPerRevFormat = createFormat({decimals:(unit == MM ? 3 : 4), forceDecimal:true});
var pitchFormat = createFormat({decimals:(unit == MM ? 3 : 4), forceDecimal:true});
var toolFormat = createFormat({decimals:0});
var rpmFormat = createFormat({decimals:0});
var secFormat = createFormat({decimals:3, forceDecimal:true}); // seconds - range 0.001-1000
var milliFormat = createFormat({decimals:0}); // milliseconds // range 1-9999
var taperFormat = createFormat({decimals:1, scale:DEG});
var peckFormat = createFormat({decimals:(unit == MM ? 3 : 4), forceDecimal:true});
var xOutput = createOutputVariable({prefix:"X"}, xyzFormat);
var yOutput = createOutputVariable({prefix:"Y"}, xyzFormat);
var zOutput = createOutputVariable({onchange:function() {retracted = false;}, prefix:"Z"}, xyzFormat);
var aOutput = createOutputVariable({prefix:"A"}, abcFormat);
var bOutput = createOutputVariable({prefix:"B"}, abcFormat);
var cOutput = createOutputVariable({prefix:"C"}, abcFormat);
var feedOutput = createOutputVariable({prefix:"F"}, feedFormat);
var inverseTimeOutput = createOutputVariable({prefix:"F", control:CONTROL_FORCE}, feedFormat);
var pitchOutput = createOutputVariable({prefix:"F", control:CONTROL_FORCE}, pitchFormat);
var sOutput = createOutputVariable({prefix:"S", control:CONTROL_FORCE}, rpmFormat);
var dOutput = createOutputVariable({}, dFormat);
var peckOutput = createVariable({prefix:"Q", force:true}, peckFormat);
// circular output
var iOutput = createOutputVariable({prefix:"I", control:CONTROL_FORCE}, xyzFormat);
var jOutput = createOutputVariable({prefix:"J", control:CONTROL_FORCE}, xyzFormat);
var kOutput = createOutputVariable({prefix:"K", control:CONTROL_FORCE}, xyzFormat);
var gMotionModal = createOutputVariable({onchange:function() {if (skipBlock) {forceModals(gMotionModal);}}}, gFormat); // modal group 1 // G0-G3, ...
var gPlaneModal = createOutputVariable({onchange:function() {if (skipBlock) {forceModals(gPlaneModal);} forceModals(gMotionModal);}}, gFormat); // modal group 2 // G17-19
var gAbsIncModal = createOutputVariable({onchange:function() {if (skipBlock) {forceModals(gAbsIncModal);}}}, gFormat); // modal group 3 // G90-91
var gFeedModeModal = createOutputVariable({}, gFormat); // modal group 5 // G93-94
var gUnitModal = createOutputVariable({}, gFormat); // modal group 6 // G20-21
var gCycleModal = createOutputVariable({}, gFormat); // modal group 9 // G81, ...
var gRetractModal = createOutputVariable({control:CONTROL_FORCE}, gFormat); // modal group 10 // G98-99
var gRotationModal = createOutputVariable({
onchange: function () {
if (probeVariables.probeAngleMethod == "G68") {
probeVariables.outputRotationCodes = true;
}
}
}, gFormat); // modal group 16 // G68-G69
var mClampModal = createModalGroup(
{strict:false},
[
[10, 11], // 4th axis clamp / unclamp
[12, 13] // 5th axis clamp / unclamp
],
mFormat
);
// fixed settings
var firstFeedParameter = 100; // the first variable to use with parametric feed
var forceResetWorkPlane = false; // enable to force reset of machine ABC on new orientation
var minimumCyclePoints = 5; // minimum number of points in cycle operation to consider for subprogram
var useDwoForPositioning = true; // specifies to use the DWO feature for XY positioning for multi-axis operations
var allowIndexingWCSProbing = false; // specifies that probe WCS with tool orientation is supported
var probeVariables = {
outputRotationCodes: false, // defines if it is required to output rotation codes
probeAngleMethod : "OFF", // OFF, AXIS_ROT, G68, G54.4
compensationXY : undefined,
rotationalAxis : -1
};
var SUB_UNKNOWN = 0;
var SUB_PATTERN = 1;
var SUB_CYCLE = 2;
// collected state
var sequenceNumber;
var currentWorkOffset;
var coolantPressure = "";
var currentCoolantPressure = "";
var optionalSection = false;
var forceSpindleSpeed = false;
var activeMovements; // do not use by default
var currentFeedId;
var maximumCircularRadiiDifference = toPreciseUnit(0.005, MM);
var maximumLineLength = 80; // the maximum number of charaters allowed in a line
var subprograms = [];
var currentPattern = -1;
var firstPattern = false;
var currentSubprogram;
var lastSubprogram;
var initialSubprogramNumber = 90000;
var definedPatterns = new Array();
var incrementalMode = false;
var saveShowSequenceNumbers;
var cycleSubprogramIsActive = false;
var patternIsActive = false;
var lastOperationComment = "";
var incrementalSubprogram;
var retracted = false; // specifies that the tool has been retracted to the safe plane
var measureTool = false;
var tapping = false;
var useABCPrepositioning = true; // disable to use G253
var useDWOCycles = false; // do not work on machine at this time, Haas supposed to be fixing this
var axisIsClamped = true; // rotary axes are clamped
var bDirection = -2; // default setting
var highRotaryFeedrate = (unit == IN) ? 200 : 5000; // high feed for positioning rotary axes, too high can cause machine fault
var previousABCPosition = new Vector(0, 0, 0);
var currentRetractPlane = 0; // current Z retract level
// used to convert blocks to optional for safeStartAllOperations, might get used outside of onSection
var operationNeedsSafeStart = false;
/**
Writes the specified block.
*/
var skipBlock = false;
function writeBlock() {
var text = formatWords(arguments);
if (!text) {
return;
}
var maximumSequenceNumber = ((getProperty("useSubroutines") == "allOperations") || (getProperty("useSubroutines") == "patterns") ||
(getProperty("useSubroutines") == "cycles")) ? initialSubprogramNumber : 99999;
if (getProperty("showSequenceNumbers") == "true") {
if (sequenceNumber >= maximumSequenceNumber) {
sequenceNumber = getProperty("sequenceNumberStart");
}
if (optionalSection || skipBlock) {
if (text) {
writeWords("/", "N" + sequenceNumber, text);
}
} else {
writeWords2("N" + sequenceNumber, arguments);
}
sequenceNumber += getProperty("sequenceNumberIncrement");
} else {
if (optionalSection || skipBlock) {
writeWords2("/", arguments);
} else {
writeWords(arguments);
}
}
skipBlock = false;
}
/**
Writes the specified block - used for tool changes only.
*/
function writeToolBlock() {
var show = getProperty("showSequenceNumbers");
setProperty("showSequenceNumbers", (show == "true" || show == "toolChange") ? "true" : "false");
writeBlock(arguments);
setProperty("showSequenceNumbers", show);
}
/**
Writes the specified optional block.
*/
function writeOptionalBlock() {
skipBlock = true;
writeBlock(arguments);
}
function formatComment(text) {
return "(" + String(text).replace(/[()]/g, "") + ")";
}
/**
Output a comment.
*/
function writeComment(text) {
writeln(formatComment(text.substr(0, maximumLineLength - 2)));
}
/**
Output debug line
*/
function writeDebug(text) {
writeComment("DEBUG - " + text);
log("DEBUG - " + text);
}
/**
Returns the matching HAAS tool type for the tool.
*/
function getHaasToolType(toolType) {
switch (toolType) {
case TOOL_DRILL:
case TOOL_REAMER:
return 1; // drill
case TOOL_TAP_RIGHT_HAND:
case TOOL_TAP_LEFT_HAND:
return 2; // tap
case TOOL_MILLING_FACE:
case TOOL_MILLING_SLOT:
case TOOL_BORING_BAR:
return 3; // shell mill
case TOOL_MILLING_END_FLAT:
case TOOL_MILLING_END_BULLNOSE:
case TOOL_MILLING_TAPERED:
case TOOL_MILLING_DOVETAIL:
case TOOL_MILLING_RADIUS:
return 4; // end mill
case TOOL_DRILL_SPOT:
case TOOL_MILLING_CHAMFER:
case TOOL_DRILL_CENTER:
case TOOL_COUNTER_SINK:
case TOOL_COUNTER_BORE:
case TOOL_MILLING_THREAD:
case TOOL_MILLING_FORM:
return 5; // center drill
case TOOL_MILLING_END_BALL:
case TOOL_MILLING_LOLLIPOP:
return 6; // ball nose
case TOOL_PROBE:
return 7; // probe
default:
error(localize("Invalid HAAS tool type."));
return -1;
}
}
function getHaasProbingType(toolType, use9023) {
switch (getHaasToolType(toolType)) {
case 3:
case 4:
return (use9023 ? 23 : 1); // rotate
case 1:
case 2:
case 5:
case 6:
case 7:
return (use9023 ? 12 : 2); // non rotate
case 0:
return (use9023 ? 13 : 3); // rotate length and dia
default:
error(localize("Invalid HAAS tool type."));
return -1;
}
}
function writeToolCycleBlock(tool) {
writeOptionalBlock("T" + toolFormat.format(tool.number), mFormat.format(6)); // get tool
writeOptionalBlock(mFormat.format(0)); // wait for operator
}
function prepareForToolCheck() {
onCommand(COMMAND_STOP_SPINDLE);
onCommand(COMMAND_COOLANT_OFF);
// cancel TCP so that tool doesn't follow tables
if (currentSection.isMultiAxis() && operationSupportsTCP) {
disableLengthCompensation(false, "TCPC OFF");
}
if ((currentSection.isMultiAxis() && getCurrentDirection().length != 0) ||
(currentMachineABC != undefined && currentMachineABC.length != 0)) {
setWorkPlane(new Vector(0, 0, 0));
forceWorkPlane();
}
}
function writeToolMeasureBlock(tool, preMeasure) {
var writeFunction = measureTool ? writeBlock : writeOptionalBlock;
var comment = measureTool ? formatComment("MEASURE TOOL") : "";
if (!preMeasure) {
prepareForToolCheck();
}
if (true) { // use Macro P9023 to measure tools
var probingType = getHaasProbingType(tool.type, true);
writeFunction(
gFormat.format(65),
"P9023",
"A" + probingType + ".",
"T" + toolFormat.format(tool.number),
conditional((probingType != 12), "H" + xyzFormat.format(getBodyLength(tool))),
conditional((probingType != 12), "D" + xyzFormat.format(tool.diameter)),
comment
);
} else { // use Macro P9995 to measure tools
writeFunction("T" + toolFormat.format(tool.number), mFormat.format(6)); // get tool
writeFunction(
gFormat.format(65),
"P9995",
"A0.",
"B" + getHaasToolType(tool.type) + ".",
"C" + getHaasProbingType(tool.type, false) + ".",
"T" + toolFormat.format(tool.number),
"E" + xyzFormat.format(getBodyLength(tool)),
"D" + xyzFormat.format(tool.diameter),
"K" + xyzFormat.format(0.1),
"I0.",
comment
); // probe tool
}
measureTool = false;
}
// Start of machine configuration logic
var compensateToolLength = false; // add the tool length to the pivot distance for nonTCP rotary heads
var virtualTooltip = false; // translate the pivot point to the virtual tool tip for nonTCP rotary heads
// internal variables, do not change
var receivedMachineConfiguration;
var operationSupportsTCP;
var multiAxisFeedrate;
function activateMachine() {
// disable unsupported rotary axes output
if (!machineConfiguration.isMachineCoordinate(0) && (typeof aOutput != "undefined")) {
aOutput.disable();
}
if (!machineConfiguration.isMachineCoordinate(1) && (typeof bOutput != "undefined")) {
bOutput.disable();
}
if (!machineConfiguration.isMachineCoordinate(2) && (typeof cOutput != "undefined")) {
cOutput.disable();
}
// don't need to modify any settings if 3-axis machine
if (!machineConfiguration.isMultiAxisConfiguration()) {
return;
}
// setup usage of multiAxisFeatures
useDWO = getProperty("useMultiAxisFeatures") != undefined ? getProperty("useMultiAxisFeatures") :
(typeof useDWO != "undefined" ? useDWO : false);
useABCPrepositioning = getProperty("useABCPrepositioning") != undefined ? getProperty("useABCPrepositioning") :
(typeof useABCPrepositioning != "undefined" ? useABCPrepositioning : false);
if (receivedMachineConfiguration && machineConfiguration.getMaximumFeedrate() > 0) {
highFeedrate = machineConfiguration.getMaximumFeedrate();
}
// save multi-axis feedrate settings from machine configuration
var mode = machineConfiguration.getMultiAxisFeedrateMode();
var type = mode == FEED_INVERSE_TIME ? machineConfiguration.getMultiAxisFeedrateInverseTimeUnits() :
(mode == FEED_DPM ? machineConfiguration.getMultiAxisFeedrateDPMType() : DPM_STANDARD);
multiAxisFeedrate = {
mode : mode,
maximum : machineConfiguration.getMultiAxisFeedrateMaximum(),
type : type,
tolerance: mode == FEED_DPM ? machineConfiguration.getMultiAxisFeedrateOutputTolerance() : 0,
bpwRatio : mode == FEED_DPM ? machineConfiguration.getMultiAxisFeedrateBpwRatio() : 1
};
// setup of retract/reconfigure TAG: Only needed until post kernel supports these machine config settings
if (receivedMachineConfiguration && machineConfiguration.performRewinds()) {
safeRetractDistance = machineConfiguration.getSafeRetractDistance();
safePlungeFeed = machineConfiguration.getSafePlungeFeedrate();
safeRetractFeed = machineConfiguration.getSafeRetractFeedrate();
}
if (typeof safeRetractDistance == "number" && getProperty("safeRetractDistance") != undefined && getProperty("safeRetractDistance") != 0) {
safeRetractDistance = getProperty("safeRetractDistance");
}
// setup for head configurations
if (machineConfiguration.isHeadConfiguration()) {
compensateToolLength = typeof compensateToolLength == "undefined" ? false : compensateToolLength;
}
// calculate the ABC angles and adjust the points for multi-axis operations
// rotary heads may require the tool length be added to the pivot length
// so we need to optimize each section individually
if (machineConfiguration.isHeadConfiguration() && compensateToolLength) {
for (var i = 0; i < getNumberOfSections(); ++i) {
var section = getSection(i);
if (section.isMultiAxis()) {
machineConfiguration.setToolLength(getBodyLength(section.getTool())); // define the tool length for head adjustments
section.optimizeMachineAnglesByMachine(machineConfiguration, OPTIMIZE_AXIS);
}
}
} else { // tables and rotary heads with TCP support can be optimized with a single call
optimizeMachineAngles2(OPTIMIZE_AXIS);
}
}
function getBodyLength(tool) {
for (var i = 0; i < getNumberOfSections(); ++i) {
var section = getSection(i);
if (tool.number == section.getTool().number) {
return section.getParameter("operation:tool_overallLength", tool.bodyLength + tool.holderLength);
}
}
return tool.bodyLength + tool.holderLength;
}
function defineMachine() {
var useTCP = true;
if (receivedMachineConfiguration) {
var bAxis = machineConfiguration.getAxisU();
var cAxis = machineConfiguration.getAxisV();
if ((!bAxis.isEnabled() || !bAxis.isHead()) ||
(!cAxis.isEnabled() || cAxis.getCoordinate() != 2 || !isSameDirection(cAxis.getAxis().abs, new Vector(0, 0, 1)) || !cAxis.isHead())) {
warning(localize("The provided CAM machine configuration is overwritten by the postprocessor."));
receivedMachineConfiguration = false;
}
}
if (!receivedMachineConfiguration) { // CAM provided machine configuration takes precedence
// if (true) { // hardcoded machine configuration takes precedence
var bAxis = createAxis({coordinate:1, table:false, axis:[0, -1, 0], range:[-120 - 0.0001, 120 + 0.0001], preference:parseInt(getProperty("preferredTilt"), 10), cyclic:false, tcp:useTCP});
var cAxis = createAxis({coordinate:2, table:false, axis:[0, 0, -1], range:[-245 - 0.0001, 240 + 0.0001], preference:0, cyclic:false, tcp:useTCP});
machineConfiguration = new MachineConfiguration(bAxis, cAxis);
setMachineConfiguration(machineConfiguration);
// retract / reconfigure
var performRewinds = true; // set to true to enable the rewind/reconfigure logic
if (performRewinds) {
machineConfiguration.enableMachineRewinds(); // enables the retract/reconfigure logic
safeRetractDistance = (unit == IN) ? 1 : 25; // additional distance to retract out of stock, can be overridden with a property
safeRetractFeed = (unit == IN) ? 20 : 500; // retract feed rate
safePlungeFeed = (unit == IN) ? 10 : 250; // plunge feed rate
machineConfiguration.setSafeRetractDistance(safeRetractDistance);
machineConfiguration.setSafeRetractFeedrate(safeRetractFeed);
machineConfiguration.setSafePlungeFeedrate(safePlungeFeed);
var stockExpansion = new Vector(toPreciseUnit(0.1, IN), toPreciseUnit(0.1, IN), toPreciseUnit(0.1, IN)); // expand stock XYZ values
machineConfiguration.setRewindStockExpansion(stockExpansion);
}
// multi-axis feedrates
if (machineConfiguration.isMultiAxisConfiguration()) {
machineConfiguration.setMultiAxisFeedrate(
useTCP ? FEED_FPM : getProperty("useDPMFeeds") ? FEED_DPM : FEED_INVERSE_TIME,
9999.99, // maximum output value for inverse time feed rates
getProperty("useDPMFeeds") ? DPM_COMBINATION : INVERSE_MINUTES, // INVERSE_MINUTES/INVERSE_SECONDS or DPM_COMBINATION/DPM_STANDARD
0.5, // tolerance to determine when the DPM feed has changed
1.0 // ratio of rotary accuracy to linear accuracy for DPM calculations
);
setMachineConfiguration(machineConfiguration);
}
/* home positions */
machineConfiguration.setHomePositionX(getProperty("homePositionX"));
machineConfiguration.setHomePositionY(getProperty("homePositionY"));
machineConfiguration.setRetractPlane(getProperty("homePositionZ"));
if (receivedMachineConfiguration) {
warning(localize("The provided CAM machine configuration is overwritten by the postprocessor."));
receivedMachineConfiguration = false; // CAM provided machine configuration is overwritten
}
}
}
// End of machine configuration logic
function onOpen() {
// convert unit-based properties
if (typeof parseSpatialProperties == "function") {
parseSpatialProperties();
}
receivedMachineConfiguration = machineConfiguration.isReceived();
if (typeof defineMachine == "function") {
defineMachine(); // hardcoded machine configuration
}
activateMachine(); // enable the machine optimizations and settings
if (getProperty("useRadius")) {
maximumCircularSweep = toRad(90); // avoid potential center calculation errors for CNC
}
if (!getProperty("useMultiAxisFeatures")) {
useDwoForPositioning = false;
}
gRotationModal.format(69); // Default to G69 Rotation Off
mClampModal.format(10); // Default 4th axis modal code to be clamped
mClampModal.format(12); // Default 5th axis modal code to be clamped
minRetract = toPreciseUnit(2, IN);
if (getProperty("safeRetractDistanceZ") < minRetract) {
error(subst(localize("The Safe Z-retract distance for head rotations must be at least %1"), minRetract) +
(unit == IN ? "in." : "mm."));
return;
}
if (toPreciseUnit(highFeedrate, MM) <= 0) {
error(localize("You must set 'highFeedrate' because axes are not synchronized for rapid traversal."));
return;
}
if (!getProperty("separateWordsWithSpace")) {
setWordSeparator("");
}
sequenceNumber = getProperty("sequenceNumberStart");
writeln("%");
if (programName) {
var programId;
try {
programId = getAsInt(programName);
} catch (e) {
error(localize("Program name must be a number."));
return;
}
if (!((programId >= 1) && (programId <= 99999))) {
error(localize("Program number is out of range."));
return;
}
writeln(
"O" + oFormat.format(programId) +
conditional(programComment, " " + formatComment(programComment.substr(0, maximumLineLength - 2 - ("O" + oFormat.format(programId)).length - 1)))
);
lastSubprogram = (initialSubprogramNumber - 1);
} else {
error(localize("Program name has not been specified."));
return;
}
if (getProperty("useG0")) {
writeComment(localize("CAUTION: Using G0. Make sure that Setting 335 is set to 'Linear + Rotary'."));
} else {
writeComment(subst(localize("Using high feed G1 F%1 instead of G0."), feedFormat.format(toPreciseUnit(highFeedrate, MM))));
}
if (getProperty("writeVersion")) {
if ((typeof getHeaderVersion == "function") && getHeaderVersion()) {
writeComment(localize("post version") + ": " + getHeaderVersion());
}
if ((typeof getHeaderDate == "function") && getHeaderDate()) {
writeComment(localize("post modified") + ": " + getHeaderDate());
}
}
// dump machine configuration
var vendor = machineConfiguration.getVendor();
var model = machineConfiguration.getModel();
var description = machineConfiguration.getDescription();
if (getProperty("writeMachine") && (vendor || model || description)) {
writeComment(localize("Machine"));
if (vendor) {
writeComment(" " + localize("vendor") + ": " + vendor);
}
if (model) {
writeComment(" " + localize("model") + ": " + model);
}
if (description) {
writeComment(" " + localize("description") + ": " + description);
}
}
// dump tool information
if (getProperty("writeTools")) {
var zRanges = {};
if (is3D()) {
var numberOfSections = getNumberOfSections();
for (var i = 0; i < numberOfSections; ++i) {
var section = getSection(i);
var zRange = section.getGlobalZRange();
var tool = section.getTool();
if (zRanges[tool.number]) {
zRanges[tool.number].expandToRange(zRange);
} else {
zRanges[tool.number] = zRange;
}
}
}
var tools = getToolTable();
if (tools.getNumberOfTools() > 0) {
for (var i = 0; i < tools.getNumberOfTools(); ++i) {
var tool = tools.getTool(i);
var comment = "T" + toolFormat.format(tool.number) + " " +
"D=" + xyzFormat.format(tool.diameter) + " " +
localize("CR") + "=" + xyzFormat.format(tool.cornerRadius);
if ((tool.taperAngle > 0) && (tool.taperAngle < Math.PI)) {
comment += " " + localize("TAPER") + "=" + taperFormat.format(tool.taperAngle) + localize("deg");
}
if (zRanges[tool.number]) {
comment += " - " + localize("ZMIN") + "=" + xyzFormat.format(zRanges[tool.number].getMinimum());
}
comment += " - " + getToolTypeName(tool.type);
writeComment(comment);
}
}
}
// optionally cycle through all tools
if (getProperty("optionallyCycleToolsAtStart") || getProperty("measureTools")) {
var tools = getToolTable();
if (tools.getNumberOfTools() > 0) {
writeln("");
writeOptionalBlock(mFormat.format(0), formatComment(localize("Read note"))); // wait for operator
writeComment(localize("With BLOCK DELETE turned off each tool will cycle through"));
writeComment(localize("the spindle to verify that the correct tool is in the tool magazine"));
if (getProperty("measureTools")) {
writeComment(localize("and to automatically measure it"));
}
writeComment(localize("Once the tools are verified turn BLOCK DELETE on to skip verification"));
for (var i = 0; i < tools.getNumberOfTools(); ++i) {
var tool = tools.getTool(i);
if (getProperty("measureTools") && (tool.type == TOOL_PROBE)) {
continue;
}
var comment = "T" + toolFormat.format(tool.number) + " " +
"D=" + xyzFormat.format(tool.diameter) + " " +
localize("CR") + "=" + xyzFormat.format(tool.cornerRadius);
if ((tool.taperAngle > 0) && (tool.taperAngle < Math.PI)) {
comment += " " + localize("TAPER") + "=" + taperFormat.format(tool.taperAngle) + localize("deg");
}
comment += " - " + getToolTypeName(tool.type);
writeComment(comment);
if (getProperty("measureTools")) {
writeToolMeasureBlock(tool, true);
} else {
writeToolCycleBlock(tool);
}
}
}
writeln("");
}
if (false /*getProperty("useMultiAxisFeatures")*/) {
var failed = false;
var dynamicWCSs = {};
for (var i = 0; i < getNumberOfSections(); ++i) {
var section = getSection(i);
var description = section.hasParameter("operation-comment") ? section.getParameter("operation-comment") : ("#" + (i + 1));
if (!section.hasDynamicWorkOffset()) {
error(subst(localize("Dynamic work offset has not been set for operation '%1'."), description));
failed = true;
}
var o = section.getDynamicWCSOrigin();
var p = section.getDynamicWCSPlane();
if (dynamicWCSs[section.getDynamicWorkOffset()]) {
if ((Vector.diff(o, dynamicWCSs[section.getDynamicWorkOffset()].origin).length > 1e-9) ||
(Matrix.diff(p, dynamicWCSs[section.getDynamicWorkOffset()].plane).n1 > 1e-9)) {
error(subst(localize("Dynamic WCS mismatch for operation '%1'."), description));
failed = true;
}
} else {
dynamicWCSs[section.getDynamicWorkOffset()] = {origin:o, plane:p};
}
}
if (failed) {
return;
}
}
if (false) {
// check for duplicate tool number
for (var i = 0; i < getNumberOfSections(); ++i) {
var sectioni = getSection(i);
var tooli = sectioni.getTool();
for (var j = i + 1; j < getNumberOfSections(); ++j) {
var sectionj = getSection(j);
var toolj = sectionj.getTool();
if (tooli.number == toolj.number) {
if (xyzFormat.areDifferent(tooli.diameter, toolj.diameter) ||
xyzFormat.areDifferent(tooli.cornerRadius, toolj.cornerRadius) ||
abcFormat.areDifferent(tooli.taperAngle, toolj.taperAngle) ||
(tooli.numberOfFlutes != toolj.numberOfFlutes)) {
error(
subst(
localize("Using the same tool number for different cutter geometry for operation '%1' and '%2'."),
sectioni.hasParameter("operation-comment") ? sectioni.getParameter("operation-comment") : ("#" + (i + 1)),
sectionj.hasParameter("operation-comment") ? sectionj.getParameter("operation-comment") : ("#" + (j + 1))
)
);
return;
}
}
}
}
}
if ((getNumberOfSections() > 0) && (getSection(0).workOffset == 0)) {
for (var i = 0; i < getNumberOfSections(); ++i) {
if (getSection(i).workOffset > 0) {
error(localize("Using multiple work offsets is not possible if the initial work offset is 0."));
return;
}
}
}
// absolute coordinates and feed per min
writeBlock(gAbsIncModal.format(90), gFeedModeModal.format(94), gPlaneModal.format(17));
writeBlock(gFormat.format(49), gFormat.format(269));
switch (unit) {
case IN:
writeBlock(gUnitModal.format(20));
break;
case MM:
writeBlock(gUnitModal.format(21));
break;
}
// Probing Surface Inspection
if (typeof inspectionWriteVariables == "function") {
inspectionWriteVariables();
}
}
function onComment(message) {
writeComment(message);
}
/** Force output of X, Y, and Z. */
function forceXYZ() {
xOutput.reset();
yOutput.reset();
zOutput.reset();
}
/** Force output of A, B, and C. */
function forceABC() {
aOutput.reset();
bOutput.reset();
cOutput.reset();
}
function forceFeed() {
currentFeedId = undefined;
feedOutput.reset();
}
/** Force output of X, Y, Z, A, B, C, and F on next output. */
function forceAny() {
forceXYZ();
forceABC();
forceFeed();
}
function forceModals() {
if (arguments.length == 0) { // reset all modal variables listed below
if (typeof gMotionModal != "undefined") {
gMotionModal.reset();
}
if (typeof gPlaneModal != "undefined") {
gPlaneModal.reset();
}
if (typeof gAbsIncModal != "undefined") {
gAbsIncModal.reset();
}
if (typeof gFeedModeModal != "undefined") {
gFeedModeModal.reset();
}
} else {
for (var i in arguments) {
arguments[i].reset(); // only reset the modal variable passed to this function
}
}
}
var lengthCompensationActive = false;
/** Disables length compensation if currently active or if forced. */
function disableLengthCompensation(force) {
if (lengthCompensationActive || force) {
// validate(retracted, "Cannot cancel length compensation if the machine is not fully retracted.");
writeBlock(gFormat.format(49));
lengthCompensationActive = false;
}
}
// Start of smoothing logic
var smoothingSettings = {
roughing : 1, // roughing level for smoothing in automatic mode
semi : 2, // semi-roughing level for smoothing in automatic mode
semifinishing : 2, // semi-finishing level for smoothing in automatic mode
finishing : 3, // finishing level for smoothing in automatic mode
thresholdRoughing : toPreciseUnit(0.5, MM), // operations with stock/tolerance above that threshold will use roughing level in automatic mode
thresholdFinishing : toPreciseUnit(0.05, MM), // operations with stock/tolerance below that threshold will use finishing level in automatic mode
thresholdSemiFinishing: toPreciseUnit(0.1, MM), // operations with stock/tolerance above finishing and below threshold roughing that threshold will use semi finishing level in automatic mode
differenceCriteria: "level", // options: "level", "tolerance", "both". Specifies criteria when output smoothing codes
autoLevelCriteria : "stock", // use "stock" or "tolerance" to determine levels in automatic mode
cancelCompensation: false // tool length compensation must be canceled prior to changing the smoothing level
};
// collected state below, do not edit
var smoothing = {
cancel : false, // cancel tool length prior to update smoothing for this operation
isActive : false, // the current state of smoothing
isAllowed : false, // smoothing is allowed for this operation
isDifferent: false, // tells if smoothing levels/tolerances/both are different between operations
level : -1, // the active level of smoothing
tolerance : -1, // the current operation tolerance
force : false // smoothing needs to be forced out in this operation
};
function initializeSmoothing() {
var previousLevel = smoothing.level;
var previousTolerance = smoothing.tolerance;
// determine new smoothing levels and tolerances
smoothing.level = parseInt(getProperty("useSmoothing"), 10);
smoothing.level = isNaN(smoothing.level) ? -1 : smoothing.level;
smoothing.tolerance = Math.max(getParameter("operation:tolerance", smoothingSettings.thresholdFinishing), 0);
// automatically determine smoothing level
if (smoothing.level == 9999) {
if (smoothingSettings.autoLevelCriteria == "stock") { // determine auto smoothing level based on stockToLeave
var stockToLeave = xyzFormat.getResultingValue(getParameter("operation:stockToLeave", 0));
var verticalStockToLeave = xyzFormat.getResultingValue(getParameter("operation:verticalStockToLeave", 0));
if (((stockToLeave >= smoothingSettings.thresholdRoughing) && (verticalStockToLeave >= smoothingSettings.thresholdRoughing)) ||
getParameter("operation:strategy", "") == "face") {
smoothing.level = smoothingSettings.roughing; // set roughing level
} else {
if (((stockToLeave >= smoothingSettings.thresholdSemiFinishing) && (stockToLeave < smoothingSettings.thresholdRoughing)) &&
((verticalStockToLeave >= smoothingSettings.thresholdSemiFinishing) && (verticalStockToLeave < smoothingSettings.thresholdRoughing))) {
smoothing.level = smoothingSettings.semi; // set semi level
} else if (((stockToLeave >= smoothingSettings.thresholdFinishing) && (stockToLeave < smoothingSettings.thresholdSemiFinishing)) &&
((verticalStockToLeave >= smoothingSettings.thresholdFinishing) && (verticalStockToLeave < smoothingSettings.thresholdSemiFinishing))) {
smoothing.level = smoothingSettings.semifinishing; // set semi-finishing level
} else {
smoothing.level = smoothingSettings.finishing; // set finishing level
}
}
} else { // detemine auto smoothing level based on operation tolerance instead of stockToLeave
if (smoothing.tolerance >= smoothingSettings.thresholdRoughing ||
getParameter("operation:strategy", "") == "face") {
smoothing.level = smoothingSettings.roughing; // set roughing level
} else {
if (((smoothing.tolerance >= smoothingSettings.thresholdSemiFinishing) && (smoothing.tolerance < smoothingSettings.thresholdRoughing))) {
smoothing.level = smoothingSettings.semi; // set semi level
} else if (((smoothing.tolerance >= smoothingSettings.thresholdFinishing) && (smoothing.tolerance < smoothingSettings.thresholdSemiFinishing))) {
smoothing.level = smoothingSettings.semifinishing; // set semi-finishing level
} else {
smoothing.level = smoothingSettings.finishing; // set finishing level
}
}
}
}
if (smoothing.level == -1) { // useSmoothing is disabled
smoothing.isAllowed = false;
} else { // do not output smoothing for the following operations
smoothing.isAllowed = !(currentSection.getTool().type == TOOL_PROBE || currentSection.checkGroup(STRATEGY_DRILLING));
}
if (!smoothing.isAllowed) {
smoothing.level = -1;
smoothing.tolerance = -1;
}
switch (smoothingSettings.differenceCriteria) {
case "level":
smoothing.isDifferent = smoothing.level != previousLevel;
break;
case "tolerance":
smoothing.isDifferent = xyzFormat.areDifferent(smoothing.tolerance, previousTolerance);
break;
case "both":
smoothing.isDifferent = smoothing.level != previousLevel || xyzFormat.areDifferent(smoothing.tolerance, previousTolerance);
break;
default:
error(localize("Unsupported smoothing criteria."));
return;
}
// tool length compensation needs to be canceled when smoothing state/level changes
if (smoothingSettings.cancelCompensation) {
smoothing.cancel = !isFirstSection() && smoothing.isDifferent;
}
}
function setSmoothing(mode) {
if (mode == smoothing.isActive && (!mode || !smoothing.isDifferent) && !smoothing.force) {
return; // return if smoothing is already active or is not different
}
if (typeof lengthCompensationActive != "undefined" && smoothingSettings.cancelCompensation) {
validate(!lengthCompensationActive, "Length compensation is active while trying to update smoothing.");
}
if (mode) { // enable smoothing
writeBlock(
gFormat.format(187),
"P" + smoothing.level,
conditional((smoothingSettings.differenceCriteria != "level"), "E" + xyzFormat.format(smoothing.tolerance))
);
} else { // disable smoothing
writeBlock(gFormat.format(187));
}
smoothing.isActive = mode;
smoothing.force = false;
smoothing.isDifferent = false;
}
// End of smoothing logic
function FeedContext(id, description, feed) {
this.id = id;
this.description = description;
this.feed = feed;
}
function getFeed(f) {
if (activeMovements) {
var feedContext = activeMovements[movement];
if (feedContext != undefined) {
if (!feedFormat.areDifferent(feedContext.feed, f)) {
if (feedContext.id == currentFeedId) {
return ""; // nothing has changed
}
forceFeed();
currentFeedId = feedContext.id;
return "F#" + (firstFeedParameter + feedContext.id);
}
}
currentFeedId = undefined; // force Q feed next time
}
return feedOutput.format(f); // use feed value
}
function initializeActiveFeeds() {
activeMovements = new Array();
var movements = currentSection.getMovements();
var id = 0;
var activeFeeds = new Array();
if (hasParameter("operation:tool_feedCutting")) {
if (movements & ((1 << MOVEMENT_CUTTING) | (1 << MOVEMENT_LINK_TRANSITION) | (1 << MOVEMENT_EXTENDED))) {
var feedContext = new FeedContext(id, localize("Cutting"), getParameter("operation:tool_feedCutting"));
activeFeeds.push(feedContext);
activeMovements[MOVEMENT_CUTTING] = feedContext;
if (!hasParameter("operation:tool_feedTransition")) {
activeMovements[MOVEMENT_LINK_TRANSITION] = feedContext;
}
activeMovements[MOVEMENT_EXTENDED] = feedContext;
}
++id;
if (movements & (1 << MOVEMENT_PREDRILL)) {
feedContext = new FeedContext(id, localize("Predrilling"), getParameter("operation:tool_feedCutting"));
activeMovements[MOVEMENT_PREDRILL] = feedContext;
activeFeeds.push(feedContext);
}
++id;
}
if (hasParameter("operation:finishFeedrate")) {
if (movements & (1 << MOVEMENT_FINISH_CUTTING)) {
var feedContext = new FeedContext(id, localize("Finish"), getParameter("operation:finishFeedrate"));
activeFeeds.push(feedContext);
activeMovements[MOVEMENT_FINISH_CUTTING] = feedContext;
}
++id;
} else if (hasParameter("operation:tool_feedCutting")) {
if (movements & (1 << MOVEMENT_FINISH_CUTTING)) {
var feedContext = new FeedContext(id, localize("Finish"), getParameter("operation:tool_feedCutting"));
activeFeeds.push(feedContext);
activeMovements[MOVEMENT_FINISH_CUTTING] = feedContext;
}
++id;
}
if (hasParameter("operation:tool_feedEntry")) {
if (movements & (1 << MOVEMENT_LEAD_IN)) {
var feedContext = new FeedContext(id, localize("Entry"), getParameter("operation:tool_feedEntry"));
activeFeeds.push(feedContext);
activeMovements[MOVEMENT_LEAD_IN] = feedContext;
}
++id;
}
if (hasParameter("operation:tool_feedExit")) {
if (movements & (1 << MOVEMENT_LEAD_OUT)) {
var feedContext = new FeedContext(id, localize("Exit"), getParameter("operation:tool_feedExit"));
activeFeeds.push(feedContext);
activeMovements[MOVEMENT_LEAD_OUT] = feedContext;
}
++id;
}
if (hasParameter("operation:noEngagementFeedrate")) {
if (movements & (1 << MOVEMENT_LINK_DIRECT)) {
var feedContext = new FeedContext(id, localize("Direct"), getParameter("operation:noEngagementFeedrate"));
activeFeeds.push(feedContext);
activeMovements[MOVEMENT_LINK_DIRECT] = feedContext;
}
++id;
} else if (hasParameter("operation:tool_feedCutting") &&
hasParameter("operation:tool_feedEntry") &&
hasParameter("operation:tool_feedExit")) {
if (movements & (1 << MOVEMENT_LINK_DIRECT)) {
var feedContext = new FeedContext(id, localize("Direct"), Math.max(getParameter("operation:tool_feedCutting"), getParameter("operation:tool_feedEntry"), getParameter("operation:tool_feedExit")));
activeFeeds.push(feedContext);
activeMovements[MOVEMENT_LINK_DIRECT] = feedContext;
}
++id;
}
if (hasParameter("operation:reducedFeedrate")) {
if (movements & (1 << MOVEMENT_REDUCED)) {
var feedContext = new FeedContext(id, localize("Reduced"), getParameter("operation:reducedFeedrate"));
activeFeeds.push(feedContext);
activeMovements[MOVEMENT_REDUCED] = feedContext;
}
++id;
}
if (hasParameter("operation:tool_feedRamp")) {
if (movements & ((1 << MOVEMENT_RAMP) | (1 << MOVEMENT_RAMP_HELIX) | (1 << MOVEMENT_RAMP_PROFILE) | (1 << MOVEMENT_RAMP_ZIG_ZAG))) {
var feedContext = new FeedContext(id, localize("Ramping"), getParameter("operation:tool_feedRamp"));
activeFeeds.push(feedContext);
activeMovements[MOVEMENT_RAMP] = feedContext;
activeMovements[MOVEMENT_RAMP_HELIX] = feedContext;
activeMovements[MOVEMENT_RAMP_PROFILE] = feedContext;
activeMovements[MOVEMENT_RAMP_ZIG_ZAG] = feedContext;
}
++id;
}
if (hasParameter("operation:tool_feedPlunge")) {
if (movements & (1 << MOVEMENT_PLUNGE)) {
var feedContext = new FeedContext(id, localize("Plunge"), getParameter("operation:tool_feedPlunge"));
activeFeeds.push(feedContext);
activeMovements[MOVEMENT_PLUNGE] = feedContext;
}
++id;
}
if (true) { // high feed
if ((movements & (1 << MOVEMENT_HIGH_FEED)) || (highFeedMapping != HIGH_FEED_NO_MAPPING)) {
var feed;
if (hasParameter("operation:highFeedrateMode") && getParameter("operation:highFeedrateMode") != "disabled") {
feed = getParameter("operation:highFeedrate");
} else {
feed = toPreciseUnit(this.highFeedrate, MM);
}
var feedContext = new FeedContext(id, localize("High Feed"), feed);
activeFeeds.push(feedContext);
activeMovements[MOVEMENT_HIGH_FEED] = feedContext;
activeMovements[MOVEMENT_RAPID] = feedContext;
}
++id;
}
if (hasParameter("operation:tool_feedTransition")) {
if (movements & (1 << MOVEMENT_LINK_TRANSITION)) {
var feedContext = new FeedContext(id, localize("Transition"), getParameter("operation:tool_feedTransition"));
activeFeeds.push(feedContext);
activeMovements[MOVEMENT_LINK_TRANSITION] = feedContext;
}
++id;
}
for (var i = 0; i < activeFeeds.length; ++i) {
var feedContext = activeFeeds[i];
writeBlock("#" + (firstFeedParameter + feedContext.id) + "=" + feedFormat.format(feedContext.feed), formatComment(feedContext.description));
}
}
var currentWorkPlaneABC = undefined;
var activeDWO = false;
function forceWorkPlane() {
currentWorkPlaneABC = undefined;
}
function positionABC(abc, force) {
if (typeof unwindABC == "function") {
unwindABC(abc, false);
}
if (force) {
forceABC();
}
var a = aOutput.format(abc.x);
var b = bOutput.format(abc.y);
var c = cOutput.format(abc.z);
if (a || b || c) {
if (!retracted) {
if (typeof moveToSafeRetractPosition == "function") {
moveToSafeRetractPosition();
} else {
writeRetract(Z);
}
}
gMotionModal.reset();
writeBlock(gMotionModal.format(0), a, b, c);
currentMachineABC = new Vector(abc);
if (getCurrentSectionId() != -1) {
setCurrentABC(abc); // required for machine simulation
}
}
}
function defineWorkPlane(_section, _setWorkPlane) {
var abc = new Vector(0, 0, 0);
if (machineConfiguration.isMultiAxisConfiguration()) { // use 5-axis indexing for multi-axis mode
// set working plane after datum shift
if (_section.isMultiAxis()) {
cancelTransformation();
abc = _section.getInitialToolAxisABC();
if (_setWorkPlane) {
cancelWorkPlane();
if (!retracted) {
writeRetract(Z);
}
forceWorkPlane();
// onCommand(COMMAND_UNLOCK_MULTI_AXIS); // handled automatically by the control
positionABC(abc, true);
}
} else {
if (getProperty("useMultiAxisFeatures") && !tapping) {
abc = _section.workPlane.getEuler2(EULER_XYZ_S);
cancelTransformation();
} else {
abc = getWorkPlaneMachineABC(_section.workPlane, _setWorkPlane);
}
if (_setWorkPlane) {
setWorkPlane(abc);
}
}
} else { // pure 3D
var remaining = _section.workPlane;
if (!isSameDirection(remaining.forward, new Vector(0, 0, 1))) {
error(localize("Tool orientation is not supported."));
return abc;
}
setRotation(remaining);
}
if (currentSection && (currentSection.getId() == _section.getId())) {
operationSupportsTCP = (_section.isMultiAxis() || !useDWO) && _section.getOptimizedTCPMode() == OPTIMIZE_NONE;
}
return abc;
}
function cancelWorkPlane() {
if (activeDWO) {
writeBlock(gFormat.format(269)); // cancel DWO
activeDWO = false;
}
}
function setWorkPlane(abc) {
if (!machineConfiguration.isMultiAxisConfiguration()) {
return; // ignore
}
var _skipBlock = skipBlock;
if (!((currentWorkPlaneABC == undefined) ||
abcFormat.areDifferent(abc.x, currentWorkPlaneABC.x) ||
abcFormat.areDifferent(abc.y, currentWorkPlaneABC.y) ||
abcFormat.areDifferent(abc.z, currentWorkPlaneABC.z))) {
if (operationNeedsSafeStart) {
_skipBlock = true;
} else {
return; // no change
}
}
// skipBlock = _skipBlock;
// onCommand(COMMAND_UNLOCK_MULTI_AXIS);
skipBlock = _skipBlock;
cancelWorkPlane();
// skipBlock = _skipBlock;
// onCommand(COMMAND_LOCK_MULTI_AXIS);
if (getProperty("useMultiAxisFeatures") && !tapping &&
(abcFormat.isSignificant(abc.x) || abcFormat.isSignificant(abc.y) || abcFormat.isSignificant(abc.z))) {
skipBlock = _skipBlock;
writeBlock(
gFormat.format(268),
"X" + xyzFormat.format(0), "Y" + xyzFormat.format(0), "Z" + xyzFormat.format(0),
"I" + xyzFormat.format(toDeg(abc.x)), "J" + xyzFormat.format(toDeg(abc.y)), "K" + xyzFormat.format(toDeg(abc.z)),
"Q123", // EULER_ZYX
formatComment("ENABLE FCS")
); // enable Feature Coordinate System
if (!useABCPrepositioning) {
writeBlock(gFormat.format(253)); // required to rotate the head
}
activeDWO = true;
}
currentWorkPlaneABC = abc;
skipBlock = false;
}
var closestABC = true; // choose closest machine angles
var currentMachineABC = new Vector(0, 0, 0);
function getPreferenceWeight(_abc) {
var axis = new Array(machineConfiguration.getAxisU(), machineConfiguration.getAxisV(), machineConfiguration.getAxisW());
var abc = new Array(_abc.x, _abc.y, _abc.z);
var preference = new Array((bDirection == -2 ? axis[0].getPreference() : bDirection), axis[1].getPreference(), axis[2].getPreference());
var count = 0;
for (var i = 0; i < 3; ++i) {
if (axis[i].isEnabled()) {
count += ((abcFormat.getResultingValue(abc[axis[i].getCoordinate()]) * preference[i]) < 0) ? -1 : 1;
}
}
return count;
}
function remapToABC(currentABC, previousABC) {
var both = machineConfiguration.getABCByDirectionBoth(machineConfiguration.getDirection(currentABC));
var abc1 = machineConfiguration.remapToABC(both[0], previousABC);
abc1 = machineConfiguration.remapABC(abc1);
var abc2 = machineConfiguration.remapToABC(both[1], previousABC);
abc2 = machineConfiguration.remapABC(abc2);
// choose angles based on preference
var preference1 = getPreferenceWeight(abc1);
var preference2 = getPreferenceWeight(abc2);
if (preference1 > preference2) {
return abc1;
} else if (preference2 > preference1) {
return abc2;
}
// choose angles based on closest solution
if (abcFormat.getResultingValue(Vector.diff(abc1, previousABC).length) <= abcFormat.getResultingValue(Vector.diff(abc2, previousABC).length)) {
return abc1;
} else {
return abc2;
}
}
function getWorkPlaneMachineABC(workPlane, _setWorkPlane) {
var W = workPlane; // map to global frame
var abc = machineConfiguration.getABC(W);
if (closestABC && (getProperty("preferredTilt") == "0" || bDirection != -2)) {
if (currentMachineABC) {
abc = remapToABC(abc, currentMachineABC);
} else {
abc = machineConfiguration.getPreferredABC(abc);
}
} else {
abc = machineConfiguration.getPreferredABC(abc);
}
try {
abc = machineConfiguration.remapABC(abc);
if (_setWorkPlane) {
currentMachineABC = abc;
}
} catch (e) {
error(
localize("Machine angles not supported") + ":"
+ conditional(machineConfiguration.isMachineCoordinate(0), " A" + abcFormat.format(abc.x))
+ conditional(machineConfiguration.isMachineCoordinate(1), " B" + abcFormat.format(abc.y))
+ conditional(machineConfiguration.isMachineCoordinate(2), " C" + abcFormat.format(abc.z))
);
}
var direction = machineConfiguration.getDirection(abc);
if (!isSameDirection(direction, W.forward)) {
error(localize("Orientation not supported."));
}
if (!machineConfiguration.isABCSupported(abc)) {
error(
localize("Work plane is not supported") + ":"
+ conditional(machineConfiguration.isMachineCoordinate(0), " A" + abcFormat.format(abc.x))
+ conditional(machineConfiguration.isMachineCoordinate(1), " B" + abcFormat.format(abc.y))
+ conditional(machineConfiguration.isMachineCoordinate(2), " C" + abcFormat.format(abc.z))
);
}
var tcp = !getProperty("useMultiAxisFeatures") || tapping;
if (tcp) {
setRotation(W); // TCP mode
} else {
if (false) { // is not needed and does not work with head/head machines
var O = machineConfiguration.getOrientation(abc);
var R = machineConfiguration.getRemainingOrientation(abc, W);
setRotation(R);
}
}
return abc;
}
function printProbeResults() {
return currentSection.getParameter("printResults", 0) == 1;
}
function onPassThrough(text) {
var commands = String(text).split(",");
for (text in commands) {
writeBlock(commands[text]);
}
}
var manualNC = [];
function onManualNC(command, value) {
switch (command) {
case COMMAND_ACTION:
var sText1 = String(value);
var sText2 = new Array();
sText2 = sText1.split(":");
if (sText2.length != 2) {
error(localize("Invalid action command: ") + value);
return;
}
if (String(sText2[0]).toUpperCase() == "BDIRECTION") {
bDirection = parseToggle(sText2[1], "DEFAULT", "NEGATIVE", "CLOSEST", "POSITIVE");
if (bDirection == undefined) {
error(localize("bDirection must be Default, Negative, Closest, or Positive"));
return;
}
bDirection -= 2;
} else if (String(value).toUpperCase() == "VFD_LOW") {
coolantPressure = "P0";
} else if (String(value).toUpperCase() == "VFD_NORMAL") {
coolantPressure = "P1";
} else if (String(value).toUpperCase() == "VFD_HIGH") {
coolantPressure = "P2";
} else {
error(localize("Invalid action command: ") + value);
}
break;
case COMMAND_PASS_THROUGH:
manualNC.push({command:command, value:value});
break;
default:
expandManualNC(command, value);
}
}
/**
Processes the Manual NC commands
Pass the desired command to process or leave argument list blank to process all buffered commands
*/
function executeManualNC(command) {
for (var i = 0; i < manualNC.length; ++i) {
if (!command || (command == manualNC[i].command)) {
expandManualNC(manualNC[i].command, manualNC[i].value);
}
}
for (var i = manualNC.length - 1; i >= 0; --i) {
if (!command || (command == manualNC[i].command)) {
manualNC.splice(i, 1);
}
}
}
function parseToggle() {
var stat = undefined;
for (i = 1; i < arguments.length; i++) {
if (String(arguments[0]).toUpperCase() == String(arguments[i]).toUpperCase()) {
if (String(arguments[i]).toUpperCase() == "YES") {
stat = true;
} else if (String(arguments[i]).toUpperCase() == "NO") {
stat = false;
} else {
stat = i - 1;
break;
}
}
}
return stat;
}
/** Returns true if the spatial vectors are significantly different. */
function areSpatialVectorsDifferent(_vector1, _vector2) {
return (xyzFormat.getResultingValue(_vector1.x) != xyzFormat.getResultingValue(_vector2.x)) ||
(xyzFormat.getResultingValue(_vector1.y) != xyzFormat.getResultingValue(_vector2.y)) ||
(xyzFormat.getResultingValue(_vector1.z) != xyzFormat.getResultingValue(_vector2.z));
}
/** Returns true if the spatial boxes are a pure translation. */
function areSpatialBoxesTranslated(_box1, _box2) {
return !areSpatialVectorsDifferent(Vector.diff(_box1[1], _box1[0]), Vector.diff(_box2[1], _box2[0])) &&
!areSpatialVectorsDifferent(Vector.diff(_box2[0], _box1[0]), Vector.diff(_box2[1], _box1[1]));
}
/** Returns true if the spatial boxes are same. */
function areSpatialBoxesSame(_box1, _box2) {
return !areSpatialVectorsDifferent(_box1[0], _box2[0]) && !areSpatialVectorsDifferent(_box1[1], _box2[1]);
}
function subprogramDefine(_initialPosition, _abc, _retracted, _zIsOutput) {
// convert patterns into subprograms
var usePattern = false;
patternIsActive = false;
if (currentSection.isPatterned && currentSection.isPatterned() && (getProperty("useSubroutines") == "patterns")) {
currentPattern = currentSection.getPatternId();
firstPattern = true;
for (var i = 0; i < definedPatterns.length; ++i) {
if ((definedPatterns[i].patternType == SUB_PATTERN) && (currentPattern == definedPatterns[i].patternId)) {
currentSubprogram = definedPatterns[i].subProgram;
usePattern = definedPatterns[i].validPattern;
firstPattern = false;
break;
}
}
if (firstPattern) {
// determine if this is a valid pattern for creating a subprogram
usePattern = subprogramIsValid(currentSection, currentPattern, SUB_PATTERN);
if (usePattern) {
currentSubprogram = ++lastSubprogram;
}
definedPatterns.push({
patternType : SUB_PATTERN,
patternId : currentPattern,
subProgram : currentSubprogram,
validPattern : usePattern,
initialPosition: _initialPosition,
finalPosition : _initialPosition
});
}
if (usePattern) {
// make sure Z-position is output prior to subprogram call
if (!_retracted && !_zIsOutput) {
writeBlock(gMotionModal.format(0), zOutput.format(_initialPosition.z));
}
// call subprogram
writeBlock(mFormat.format(97), "P" + nFormat.format(currentSubprogram));
patternIsActive = true;
if (firstPattern) {
subprogramStart(_initialPosition, _abc, incrementalSubprogram);
} else {
skipRemainingSection();
setCurrentPosition(getFramePosition(currentSection.getFinalPosition()));
}
}
}
// Output cycle operation as subprogram
if (!usePattern && (getProperty("useSubroutines") == "cycles") && currentSection.doesStrictCycle &&
(currentSection.getNumberOfCycles() == 1) && currentSection.getNumberOfCyclePoints() >= minimumCyclePoints) {
var finalPosition = getFramePosition(currentSection.getFinalPosition());
currentPattern = currentSection.getNumberOfCyclePoints();
firstPattern = true;
for (var i = 0; i < definedPatterns.length; ++i) {
if ((definedPatterns[i].patternType == SUB_CYCLE) && (currentPattern == definedPatterns[i].patternId) &&
!areSpatialVectorsDifferent(_initialPosition, definedPatterns[i].initialPosition) &&
!areSpatialVectorsDifferent(finalPosition, definedPatterns[i].finalPosition)) {
currentSubprogram = definedPatterns[i].subProgram;
usePattern = definedPatterns[i].validPattern;
firstPattern = false;
break;
}
}
if (firstPattern) {
// determine if this is a valid pattern for creating a subprogram
usePattern = subprogramIsValid(currentSection, currentPattern, SUB_CYCLE);
if (usePattern) {
currentSubprogram = ++lastSubprogram;
}
definedPatterns.push({
patternType : SUB_CYCLE,
patternId : currentPattern,
subProgram : currentSubprogram,
validPattern : usePattern,
initialPosition: _initialPosition,
finalPosition : finalPosition
});
}
cycleSubprogramIsActive = usePattern;
}
// Output each operation as a subprogram
if (!usePattern && (getProperty("useSubroutines") == "allOperations")) {
currentSubprogram = ++lastSubprogram;
writeBlock(mFormat.format(97), "P" + nFormat.format(currentSubprogram));
firstPattern = true;
subprogramStart(_initialPosition, _abc, false);
}
}
function subprogramStart(_initialPosition, _abc, _incremental) {
redirectToBuffer();
var comment = "";
if (hasParameter("operation-comment")) {
comment = getParameter("operation-comment");
}
writeln(
"N" + nFormat.format(currentSubprogram) +
conditional(comment, formatComment(comment.substr(0, maximumLineLength - 2 - 6 - 1)))
);
saveShowSequenceNumbers = getProperty("showSequenceNumbers");
setProperty("showSequenceNumbers", "false");
if (_incremental) {
setAbsIncMode(true, _initialPosition, _abc);
}
gPlaneModal.reset();
gMotionModal.reset();
}
function subprogramEnd() {
if (firstPattern) {
writeBlock(mFormat.format(99));
writeln("");
subprograms += getRedirectionBuffer();
}
forceAny();
firstPattern = false;
setProperty("showSequenceNumbers", saveShowSequenceNumbers);
closeRedirection();
}
function subprogramIsValid(_section, _patternId, _patternType) {
var sectionId = _section.getId();
var numberOfSections = getNumberOfSections();
var validSubprogram = _patternType != SUB_CYCLE;
var masterPosition = new Array();
masterPosition[0] = getFramePosition(_section.getInitialPosition());
masterPosition[1] = getFramePosition(_section.getFinalPosition());
var tempBox = _section.getBoundingBox();
var masterBox = new Array();
masterBox[0] = getFramePosition(tempBox[0]);
masterBox[1] = getFramePosition(tempBox[1]);
var rotation = getRotation();
var translation = getTranslation();
incrementalSubprogram = undefined;
for (var i = 0; i < numberOfSections; ++i) {
var section = getSection(i);
if (section.getId() != sectionId) {
defineWorkPlane(section, false);
// check for valid pattern
if (_patternType == SUB_PATTERN) {
if (section.getPatternId() == _patternId) {
var patternPosition = new Array();
patternPosition[0] = getFramePosition(section.getInitialPosition());
patternPosition[1] = getFramePosition(section.getFinalPosition());
tempBox = section.getBoundingBox();
var patternBox = new Array();
patternBox[0] = getFramePosition(tempBox[0]);
patternBox[1] = getFramePosition(tempBox[1]);
if (areSpatialBoxesSame(masterPosition, patternPosition) && areSpatialBoxesSame(masterBox, patternBox) && !section.isMultiAxis()) {
incrementalSubprogram = incrementalSubprogram ? incrementalSubprogram : false;
} else if (!areSpatialBoxesTranslated(masterPosition, patternPosition) || !areSpatialBoxesTranslated(masterBox, patternBox)) {
validSubprogram = false;
break;
} else {
incrementalSubprogram = true;
}
}
// check for valid cycle operation
} else if (_patternType == SUB_CYCLE) {
if ((section.getNumberOfCyclePoints() == _patternId) && (section.getNumberOfCycles() == 1)) {
var patternInitial = getFramePosition(section.getInitialPosition());
var patternFinal = getFramePosition(section.getFinalPosition());
if (!areSpatialVectorsDifferent(patternInitial, masterPosition[0]) && !areSpatialVectorsDifferent(patternFinal, masterPosition[1])) {
validSubprogram = true;
break;
}
}
}
}
}
setRotation(rotation);
setTranslation(translation);
return (validSubprogram);
}
/**
* Sets xyz and abc output formats to incremental or absolute type
* @param {boolean} incremental true: Sets incremental mode, false: Sets absolute mode
* @param {Vector} xyz Linear axis values for formating
* @param {Vector} abc Rotary axis values for formating
*/
function setAbsIncMode(incremental, xyz, abc) {
var outputFormats = [xOutput, yOutput, zOutput, aOutput, bOutput, cOutput];
for (var i = 0; i < outputFormats.length; ++i) {
outputFormats[i].setType(incremental ? TYPE_INCREMENTAL : TYPE_ABSOLUTE);
if (i <= 2) { // xyz
outputFormats[i].setCurrent(xyz.getCoordinate(i));
} else { // abc
outputFormats[i].setCurrent(abc.getCoordinate(i - 3));
}
}
incrementalMode = incremental;
if (incremental) {
gAbsIncModal.reset();
}
writeBlock(gAbsIncModal.format(incremental ? 91 : 90));
}
function prePositionXYZ(initialPosition, abc, lengthOffset, newWorkPlane) {
var preposition = (!operationNeedsSafeStart &&
(abcFormat.areDifferent(abc.x, previousABCPosition.x) ||
abcFormat.areDifferent(abc.y, previousABCPosition.y) ||
abcFormat.areDifferent(abc.z, previousABCPosition.z)));
var safeStart = operationNeedsSafeStart && !preposition;
if (preposition || safeStart) {
//var _skipBlock = operationNeedsSafeStart && !(currentSection.isMultiAxis() || (!isFirstSection() && (getPreviousSection().isMultiAxis() || newWorkPlane)));
var _skipBlock = safeStart;
writeComment("PREPOSITIONING START");
if (currentSection.isMultiAxis()) {
skipBlock = _skipBlock;
onCommand(COMMAND_UNLOCK_MULTI_AXIS);
}
var dwo = !currentSection.isMultiAxis() && getProperty("useMultiAxisFeatures") && !tapping;
var W = currentSection.workPlane;
var tcpPosition;
var workpiece = getWorkpiece();
if (dwo) {
tcpPosition = W.multiply(initialPosition);
} else if (currentSection.isMultiAxis() && getProperty("centerOnMultiAxis")) { // position BC at center of model to avoid out-of-limits
tcpPosition = new Vector(
workpiece.lower.x + ((workpiece.upper.x - workpiece.lower.x) / 2),
workpiece.lower.y + ((workpiece.upper.y - workpiece.lower.y) / 2),
initialPosition.z);
} else {
tcpPosition = initialPosition;
}
var clearance = new Vector(tcpPosition.x, tcpPosition.y, workpiece.upper.z + getProperty("safeRetractDistanceZ"));
if (!retracted) {
skipBlock = _skipBlock;
writeRetract(Z);
}
var angles = (abc.isNonZero() && dwo) ? getWorkPlaneMachineABC(currentSection.workPlane, false) : abc;
skipBlock = _skipBlock;
forceABC();
for (var i = 0; i < 2; ++i) { // the order of XY and BC positioning differs based on if XY has been moved to home (forceHomeOnIndexing)
if ((!getProperty("forceHomeOnIndexing") && (i == 0)) || (getProperty("forceHomeOnIndexing") && (i == 1))) {
skipBlock = _skipBlock;
writeBlock(
gMotionModal.format(0),
xOutput.format(tcpPosition.x),
yOutput.format(tcpPosition.y),
(!currentSection.isMultiAxis() && !getProperty("forceHomeOnIndexing")) ? cOutput.format(angles.z) : "",
formatComment("PREPOSITION XY")
);
} else {
if (!currentSection.isMultiAxis() && useABCPrepositioning) {
if (!retracted) { // need to enable TCP when rotating heads at Z-level
skipBlock = _skipBlock;
writeRetractSafeZ(clearance.z, true, true, "ENABLE TCP", true);
skipBlock = _skipBlock;
prePositionABC(_skipBlock, angles, highRotaryFeedrate);
if (dwo) {
skipBlock = _skipBlock;
writeRetractSafeZ(clearance.z, true, false, "ENABLE TOOL LENGTH COMPENSATION", true);
}
lengthCompensationActive = true;
} else {
skipBlock = _skipBlock;
disableLengthCompensation(false);
skipBlock = _skipBlock;
cancelWorkPlane();
skipBlock = _skipBlock;
prePositionABC(_skipBlock, angles, 0);
feedOutput.reset();
}
}
}
}
if (retracted && dwo) {
skipBlock = _skipBlock;
writeRetractSafeZ(clearance, true, false, "POSITION IN Z", true);
forceXYZ();
}
if (dwo) {
var dwoClearance = W.getTransposed().multiply(clearance);
forceWorkPlane();
skipBlock = _skipBlock;
defineWorkPlane(currentSection, true);
forceXYZ();
skipBlock = _skipBlock;
writeBlock(
gMotionModal.format(1),
xOutput.format(dwoClearance.x),
yOutput.format(dwoClearance.y),
zOutput.format(dwoClearance.z),
getFeed(toPreciseUnit(highFeedrate, MM)),
formatComment("POSITION IN FCS")
);
// skipBlock = _skipBlock;
// onCommand(COMMAND_LOCK_MULTI_AXIS); // handled automatically by the control
} else if (!lengthCompensationActive) {
skipBlock = _skipBlock;
writeRetractSafeZ(clearance, true, false, "POSITION IN Z", true);
forceXYZ();
}
if (currentSection.isMultiAxis()) {
forceABC();
prePositionABC(_skipBlock, angles, highRotaryFeedrate);
if (currentSection.isMultiAxis() && getProperty("centerOnMultiAxis")) {
clearance = new Vector(initialPosition.x, initialPosition.y, workpiece.upper.z + getProperty("safeRetractDistanceZ"));
writeRetractSafeZ(clearance, false, false, "POSITION IN XY", true);
}
}
previousABCPosition = angles;
setCurrentABC(previousABCPosition);
if (!_skipBlock) {
writeBlock(
gMotionModal.format(getProperty("useG0") ? 0 : 1),
xOutput.format(initialPosition.x),
yOutput.format(initialPosition.y),
zOutput.format(initialPosition.z),
!getProperty("useG0") ? getFeed(toPreciseUnit(highFeedrate, MM)) : "",
formatComment("INITIAL POSITION")
);
} else {
forceXYZ();
var x = xOutput.format(initialPosition.x);
var y = yOutput.format(initialPosition.y);
if (!getProperty("useG0")) {
// axes are not synchronized
gMotionModal.reset();
feedOutput.reset();
writeBlock(gAbsIncModal.format(90), gMotionModal.format(1), x, y, getFeed(toPreciseUnit(highFeedrate, MM)));
} else {
writeBlock(gAbsIncModal.format(90), gMotionModal.format(0), x, y);
}
}
writeComment("PREPOSITIONING END");
} else { // no rotary axes change
defineWorkPlane(currentSection, true);
writeBlock(gAbsIncModal.format(90), gMotionModal.format(0), xOutput.format(initialPosition.x), yOutput.format(initialPosition.y));
writeRetractSafeZ(initialPosition.z, true, false, "", true);
}
coolantPressure = coolantPressure == "" ? getProperty("coolantPressure", "") : coolantPressure; // manual NC Action command takes precedence over property
if (!forceCoolant) {
forceCoolant = coolantPressure != currentCoolantPressure;
}
// set coolant after we have positioned at Z
setCoolant(tool.coolant);
}
function prePositionABC(_skipBlock, abc, feed) {
// protect against tool hitting tool changer
if (retracted && !getProperty("useG28")) {
var plane = calculateRetractPlane(abc);
if (plane < currentRetractPlane) {
writeBlock(gFormat.format(53), gMotionModal.format(0), "Z" + xyzFormat.format(plane));
}
}
skipBlock = _skipBlock;
var g = gMotionModal.format(feed == 0 ? 0 : 1);
var f = feed == 0 ? "" : getFeed(feed);
writeBlock(g, aOutput.format(abc.x), bOutput.format(abc.y), cOutput.format(abc.z), f, formatComment("ROTATE HEAD"));
previousABCPosition = new Vector(abc.x, abc.y, abc.z);
setCurrentABC(abc);
}
function onSection() {
var forceSectionRestart = optionalSection && !currentSection.isOptional();
optionalSection = currentSection.isOptional();
var insertToolCall = forceSectionRestart || isFirstSection() ||
currentSection.getForceToolChange && currentSection.getForceToolChange() ||
(tool.number != getPreviousSection().getTool().number);
retracted = false;
var zIsOutput = false; // true if the Z-position has been output, used for patterns
var newWorkOffset = isFirstSection() || forceSectionRestart ||
(getPreviousSection().workOffset != currentSection.workOffset); // work offset changes
var newWorkPlane = isFirstSection() || forceSectionRestart ||
!isSameDirection(getPreviousSection().getGlobalFinalToolAxis(), currentSection.getGlobalInitialToolAxis()) ||
(currentSection.isOptimizedForMachine() && getPreviousSection().isOptimizedForMachine() &&
Vector.diff(getPreviousSection().getFinalToolAxisABC(), currentSection.getInitialToolAxisABC()).length > 1e-4) ||
(!machineConfiguration.isMultiAxisConfiguration() && currentSection.isMultiAxis()) ||
(!getPreviousSection().isMultiAxis() && currentSection.isMultiAxis() ||
getPreviousSection().isMultiAxis() && !currentSection.isMultiAxis()); // force newWorkPlane between indexing and simultaneous operations
tapping = hasParameter("operation:cycleType") &&
((getParameter("operation:cycleType") == "tapping") ||
(getParameter("operation:cycleType") == "right-tapping") ||
(getParameter("operation:cycleType") == "left-tapping") ||
(getParameter("operation:cycleType") == "tapping-with-chip-breaking"));
operationNeedsSafeStart = getProperty("safeStartAllOperations") && !isFirstSection() && !insertToolCall;
knuckleAdjustmentIsActive = (getProperty("adjustKnuckleAngle") != "disabled") && is3D() && (currentSection.strategy != "drill");
safeKnuckleClearance = getWorkpiece().upper.z + toPreciseUnit(safeKnuckleDistance, IN);
// define smoothing mode
initializeSmoothing();
if ((insertToolCall && !getProperty("fastToolChange")) || newWorkOffset || newWorkPlane || toolChecked) {
// stop spindle before retract during tool change
if (insertToolCall && !isFirstSection() && !toolChecked && !getProperty("fastToolChange")) {
onCommand(COMMAND_STOP_SPINDLE);
}
if (insertToolCall && !isFirstSection()) {
onCommand(COMMAND_COOLANT_OFF);
}
// retract to safe plane
writeRetract(Z);
if (newWorkPlane && getProperty("forceHomeOnIndexing")) { // ensure move to XY home when work plane changes
forceABC();
}
if (forceResetWorkPlane && newWorkPlane) {
forceWorkPlane();
setWorkPlane(new Vector(0, 0, 0)); // reset working plane
}
}
if (hasParameter("operation-comment")) {
var comment = getParameter("operation-comment");
if (comment && ((comment !== lastOperationComment) || !patternIsActive || insertToolCall)) {
writeln("");
writeComment(comment);
lastOperationComment = comment;
} else if (!patternIsActive || insertToolCall) {
writeln("");
}
} else {
writeln("");
}
// process Manual NC commands
executeManualNC();
if (getProperty("showNotes") && hasParameter("notes")) {
var notes = getParameter("notes");
if (notes) {
var lines = String(notes).split("\n");
var r1 = new RegExp("^[\\s]+", "g");
var r2 = new RegExp("[\\s]+$", "g");
for (line in lines) {
var comment = lines[line].replace(r1, "").replace(r2, "");
if (comment) {
writeComment(comment);
}
}
}
}
if (operationNeedsSafeStart) {
if (!retracted) {
skipBlock = true;
writeRetract(Z);
}
}
if (insertToolCall || operationNeedsSafeStart) {
forceModals();
if (getProperty("fastToolChange") && !isProbeOperation()) {
currentCoolantMode = COOLANT_OFF;
} else if (insertToolCall) { // no coolant off command if safe start operation
// onCommand(COMMAND_COOLANT_OFF);
}
if (!isFirstSection() && getProperty("optionalStop") && insertToolCall) {
onCommand(COMMAND_OPTIONAL_STOP);
}
if ((tool.number > 200 && tool.number < 1000) || tool.number > 9999) {
warning(localize("Tool number out of range."));
}
skipBlock = !insertToolCall;
writeToolBlock(
"T" + toolFormat.format(tool.number),
mFormat.format(6)
);
currentRetractPlane = 0; // tool change fully retracts tool
if (tool.comment) {
writeComment(tool.comment);
}
if (measureTool) {
writeToolMeasureBlock(tool, false);
}
if (insertToolCall) {
forceWorkPlane();
newWorkPlane = true;
}
var showToolZMin = false;
if (showToolZMin) {
if (is3D()) {
var numberOfSections = getNumberOfSections();
var zRange = currentSection.getGlobalZRange();
var number = tool.number;
for (var i = currentSection.getId() + 1; i < numberOfSections; ++i) {
var section = getSection(i);
if (section.getTool().number != number) {
break;
}
zRange.expandToRange(section.getGlobalZRange());
}
writeComment(localize("ZMIN") + "=" + xyzFormat.format(zRange.getMinimum()));
}
}
}
// activate those two coolant modes before the spindle is turned on
if ((tool.coolant == COOLANT_THROUGH_TOOL) || (tool.coolant == COOLANT_AIR_THROUGH_TOOL) || (tool.coolant == COOLANT_FLOOD_THROUGH_TOOL)) {
if (!isFirstSection() && !insertToolCall && (currentCoolantMode != tool.coolant)) {
onCommand(COMMAND_STOP_SPINDLE);
forceSpindleSpeed = true;
}
setCoolant(tool.coolant);
} else if ((currentCoolantMode == COOLANT_THROUGH_TOOL) || (currentCoolantMode == COOLANT_AIR_THROUGH_TOOL) || (currentCoolantMode == COOLANT_FLOOD_THROUGH_TOOL)) {
onCommand(COMMAND_STOP_SPINDLE);
setCoolant(COOLANT_OFF);
forceSpindleSpeed = true;
}
if (toolChecked) {
forceSpindleSpeed = true; // spindle must be restarted if tool is checked without a tool change
toolChecked = false; // state of tool is not known at the beginning of a section since it could be broken for the previous section
}
var spindleChanged = tool.type != TOOL_PROBE &&
(insertToolCall || forceSpindleSpeed || isFirstSection() ||
(rpmFormat.areDifferent(spindleSpeed, sOutput.getCurrent())) ||
(tool.clockwise != getPreviousSection().getTool().clockwise));
if (spindleChanged || (operationNeedsSafeStart && tool.type != TOOL_PROBE)) {
forceSpindleSpeed = false;
if (spindleSpeed < 1) {
error(localize("Spindle speed out of range."));
return;
}
maximumSpindleRPM = machineConfiguration.getMaximumSpindleSpeed() > 0 ? machineConfiguration.getMaximumSpindleSpeed() : 20000;
if (spindleSpeed > maximumSpindleRPM) {
warning(subst(localize("Spindle speed '" + spindleSpeed + " RPM' exceeds maximum value of '%1 RPM' in operation '%2'"), maximumSpindleRPM, String(getParameter("operation-comment"))));
}
skipBlock = !spindleChanged;
writeBlock(
sOutput.format(spindleSpeed), mFormat.format(tool.clockwise ? 3 : 4)
);
}
if (getProperty("useParametricFeed") &&
hasParameter("operation-strategy") &&
(getParameter("operation-strategy") != "drill") && // legacy
!(currentSection.hasAnyCycle && currentSection.hasAnyCycle())) {
if (!insertToolCall &&
activeMovements &&
(getCurrentSectionId() > 0) &&
((getPreviousSection().getPatternId() == currentSection.getPatternId()) && (currentSection.getPatternId() != 0))) {
// use the current feeds
} else {
initializeActiveFeeds();
}
} else {
activeMovements = undefined;
}
// Output modal commands here
writeBlock(gAbsIncModal.format(90), gFeedModeModal.format(94), gPlaneModal.format(17));
// wcs
if (insertToolCall || operationNeedsSafeStart) { // force work offset when changing tool
currentWorkOffset = undefined;
skipBlock = operationNeedsSafeStart && !newWorkOffset && !insertToolCall;
}
if (currentSection.workOffset != currentWorkOffset) {
forceWorkPlane();
newWorkPlane = true;
writeBlock(currentSection.wcs);
currentWorkOffset = currentSection.workOffset;
}
forceXYZ();
if (newWorkOffset) {
forceWorkPlane();
newWorkPlane = true;
}
var abc = defineWorkPlane(currentSection, false);
setProbeAngle(); // output probe angle rotations if required
if (operationNeedsSafeStart) {
forceAny();
} else { // don't force rotaries between 3D operations
forceXYZ();
forceFeed();
}
gMotionModal.reset();
smoothing.force = operationNeedsSafeStart && (getProperty("useSmoothing") != "-1");
setSmoothing(smoothing.isAllowed);
var initialPosition = getFramePosition(currentSection.getInitialPosition());
var G = ((highFeedMapping != HIGH_FEED_NO_MAPPING) || !getProperty("useG0")) ? 1 : 0;
var F = ((highFeedMapping != HIGH_FEED_NO_MAPPING) || !getProperty("useG0")) ? getFeed(toPreciseUnit(highFeedrate, MM)) : "";
if (insertToolCall || retracted || operationNeedsSafeStart || newWorkPlane ||
(!isFirstSection() && (currentSection.isMultiAxis() != getPreviousSection().isMultiAxis()))) {
var lengthOffset = tool.lengthOffset;
if ((lengthOffset > 200 && lengthOffset < 1000) || lengthOffset > 9999) {
error(localize("Length offset out of range."));
return;
}
gMotionModal.reset();
prePositionXYZ(initialPosition, abc, lengthOffset, newWorkPlane);
zIsOutput = true;
gMotionModal.reset();
} else {
var x = xOutput.format(initialPosition.x);
var y = yOutput.format(initialPosition.y);
if (x && y) {
// axes are not synchronized
writeBlock(gAbsIncModal.format(90), gMotionModal.format(G), x, y, F);
} else {
writeBlock(gAbsIncModal.format(90), gMotionModal.format(0), x, y);
}
}
if (insertToolCall || operationNeedsSafeStart) {
if (getProperty("preloadTool")) {
var nextTool = getNextTool(tool.number);
if (nextTool) {
skipBlock = !insertToolCall;
writeBlock("T" + toolFormat.format(nextTool.number));
} else {
// preload first tool
var section = getSection(0);
var firstToolNumber = section.getTool().number;
if (tool.number != firstToolNumber) {
skipBlock = !insertToolCall;
writeBlock("T" + toolFormat.format(firstToolNumber));
}
}
}
}
if (isProbeOperation()) {
validate(probeVariables.probeAngleMethod != "G68", "You cannot probe while G68 Rotation is in effect.");
validate(probeVariables.probeAngleMethod != "G54.4", "You cannot probe while workpiece setting error compensation G54.4 is enabled.");
writeBlock(gFormat.format(65), "P" + 9832); // spin the probe on
inspectionCreateResultsFileHeader();
} else {
if (isInspectionOperation() && (typeof inspectionProcessSectionStart == "function")) {
inspectionProcessSectionStart();
}
}
// define subprogram
subprogramDefine(initialPosition, abc, retracted, zIsOutput);
}
function onDwell(seconds) {
if (seconds > 99999.999) {
warning(localize("Dwelling time is out of range."));
}
seconds = clamp(0.001, seconds, 99999.999);
writeBlock(gFeedModeModal.format(94), gFormat.format(4), "P" + milliFormat.format(seconds * 1000));
}
function onSpindleSpeed(spindleSpeed) {
writeBlock(sOutput.format(spindleSpeed));
}
function onCycle() {
writeBlock(gPlaneModal.format(17));
}
function getCommonCycle(x, y, z, r, c) {
forceXYZ(); // force xyz on first drill hole of any cycle
if (incrementalMode) {
zOutput.format(c);
return [xOutput.format(x), yOutput.format(y),
"Z" + xyzFormat.format(z - r),
"R" + xyzFormat.format(r - c)];
} else {
return [xOutput.format(x), yOutput.format(y),
zOutput.format(z),
"R" + xyzFormat.format(r)];
}
}
function setCyclePosition(_position) {
switch (gPlaneModal.getCurrent()) {
case 17: // XY
zOutput.format(_position);
break;
case 18: // ZX
yOutput.format(_position);
break;
case 19: // YZ
xOutput.format(_position);
break;
}
}
/** Convert approach to sign. */
function approach(value) {
validate((value == "positive") || (value == "negative"), "Invalid approach.");
return (value == "positive") ? 1 : -1;
}
function setProbeAngleMethod() {
probeVariables.probeAngleMethod = (machineConfiguration.getNumberOfAxes() < 5 || is3D()) ? (getProperty("useG54x4") ? "G54.4" : "G68") : "UNSUPPORTED";
var axes = [machineConfiguration.getAxisU(), machineConfiguration.getAxisV(), machineConfiguration.getAxisW()];
for (var i = 0; i < axes.length; ++i) {
if (axes[i].isEnabled() && isSameDirection((axes[i].getAxis()).getAbsolute(), new Vector(0, 0, 1)) && axes[i].isTable()) {
probeVariables.probeAngleMethod = "AXIS_ROT";
probeVariables.rotationalAxis = axes[i].getCoordinate();
break;
}
}
probeVariables.outputRotationCodes = true;
}
/**
Output rotation offset based on angular probing cycle.
*/
function setProbeAngle() {
if (probeVariables.outputRotationCodes) {
var probeOutputWorkOffset = currentSection.probeWorkOffset;
validate(probeOutputWorkOffset <= 6, "Angular Probing only supports work offsets 1-6.");
if (probeVariables.probeAngleMethod == "G68" && (Vector.diff(currentSection.getGlobalInitialToolAxis(), new Vector(0, 0, 1)).length > 1e-4)) {
error(localize("You cannot use multi axis toolpaths while G68 Rotation is in effect."));
}
var validateWorkOffset = false;
switch (probeVariables.probeAngleMethod) {
case "G54.4":
var param = 26000 + (probeOutputWorkOffset * 10);
writeBlock("#" + param + "=#135");
writeBlock("#" + (param + 1) + "=#136");
writeBlock("#" + (param + 5) + "=#144");
writeBlock(gFormat.format(54.4), "P" + probeOutputWorkOffset);
break;
case "G68":
gRotationModal.reset();
gAbsIncModal.reset();
writeBlock(gRotationModal.format(68), gAbsIncModal.format(90), probeVariables.compensationXY, "R[#194]");
validateWorkOffset = true;
break;
case "AXIS_ROT":
var param = 5200 + probeOutputWorkOffset * 20 + probeVariables.rotationalAxis + 4;
writeBlock("#" + param + " = " + "[#" + param + " + #194]");
forceWorkPlane(); // force workplane to rotate ABC in order to apply rotation offsets
currentWorkOffset = undefined; // force WCS output to make use of updated parameters
validateWorkOffset = true;
break;
default:
error(localize("Angular Probing is not supported for this machine configuration."));
return;
}
if (validateWorkOffset) {
for (var i = currentSection.getId(); i < getNumberOfSections(); ++i) {
if (getSection(i).workOffset != currentSection.workOffset) {
error(localize("WCS offset cannot change while using angle rotation compensation."));
return;
}
}
}
probeVariables.outputRotationCodes = false;
}
}
function protectedProbeMove(_cycle, x, y, z) {
var _x = xOutput.format(x);
var _y = yOutput.format(y);
var _z = zOutput.format(z);
if (_z && z >= getCurrentPosition().z) {
writeBlock(gFormat.format(65), "P" + 9810, _z, getFeed(cycle.feedrate)); // protected positioning move
}
if (_x || _y) {
writeBlock(gFormat.format(65), "P" + 9810, _x, _y, getFeed(toPreciseUnit(highFeedrate, MM))); // protected positioning move
}
if (_z && z < getCurrentPosition().z) {
writeBlock(gFormat.format(65), "P" + 9810, _z, getFeed(cycle.feedrate)); // protected positioning move
}
}
/**
Cancel WCS rotation when needed.
*/
function cancelG68Rotation(force) {
if (force) {
gRotationModal.reset();
}
writeBlock(gRotationModal.format(69));
}
function repositionToCycleRetract(_cycle, x, y, z) {
var toolAxis = currentSection.workPlane.forward;
var position = Vector.sum(new Vector(x, y, z), Vector.product(toolAxis, _cycle.retract - _cycle.bottom));
onRapid(position.x, position.y, position.z);
}
function onCyclePoint(x, y, z) {
if (isInspectionOperation() && (typeof inspectionCycleInspect == "function")) {
inspectionCycleInspect(cycle, x, y, z);
return;
}
if (tapping && !isSameDirection(currentSection.workPlane.forward, new Vector(0, 0, 1))) {
if (cycleType == "tapping-with-chip-breaking") {
error(localize("Tapping with chip breaking is not allowed outside of the XY-plane"));
}
repositionToCycleClearance(cycle, x, y, z);
repositionToCycleRetract(cycle, x, y, z);
gCycleModal.reset();
forceXYZ();
var tappingFPM = tool.getThreadPitch() * rpmFormat.getResultingValue(spindleSpeed);
var F = (getProperty("useG95forTapping") ? tool.getThreadPitch() : tappingFPM);
if (getProperty("useG95forTapping")) {
writeBlock(gFeedModeModal.format(95));
}
writeBlock(
gCycleModal.format((tool.type == TOOL_TAP_LEFT_HAND) ? 174 : 184),
xOutput.format(x), yOutput.format(y), zOutput.format(z),
getProperty("useG95forTapping") ? pitchOutput.format(F) : feedOutput.format(F));
onCycleEnd();
return;
}
if (!isSameDirection(getRotation().forward, new Vector(0, 0, 1)) ||
(!isSameDirection(currentSection.workPlane.forward, new Vector(0, 0, 1)) && !useDWOCycles)) {
expandCyclePoint(x, y, z);
return;
}
if (isProbeOperation()) {
if (!isSameDirection(currentSection.workPlane.forward, new Vector(0, 0, 1))) {
if (!allowIndexingWCSProbing && currentSection.strategy == "probe") {
error(localize("Updating WCS / work offset using probing is only supported by the CNC in the WCS frame."));
return;
} else if (getProperty("useMultiAxisFeatures")) {
error(localize("Your machine does not support the selected probing operation with DWO enabled."));
return;
}
}
if (printProbeResults()) {
writeProbingToolpathInformation(z - cycle.depth + tool.diameter / 2);
inspectionWriteCADTransform();
inspectionWriteWorkplaneTransform();
if (typeof inspectionWriteVariables == "function") {
inspectionVariables.pointNumber += 1;
}
}
protectedProbeMove(cycle, x, y, z);
}
var forceCycle = false;
switch (cycleType) {
case "tapping-with-chip-breaking":
case "left-tapping-with-chip-breaking":
case "right-tapping-with-chip-breaking":
forceCycle = true;
if (!isFirstCyclePoint()) {
writeBlock(gCycleModal.format(80));
gMotionModal.reset();
}
}
if (forceCycle || isFirstCyclePoint() || isProbeOperation()) {
if (!isProbeOperation()) {
// return to initial Z which is clearance plane and set absolute mode
repositionToCycleClearance(cycle, x, y, z);
}
if (currentSection.feedMode == FEED_PER_REVOLUTION) {
feedOutput.setFormat(feedPerRevFormat); // apply feedPerRevFormat to feedOutput
writeBlock(gFeedModeModal.format(95));
}
var F = cycle.feedrate;
var P = !cycle.dwell ? 0 : clamp(1, cycle.dwell * 1000, 99999999); // in milliseconds
switch (cycleType) {
case "drilling":
writeBlock(
gRetractModal.format(98), gCycleModal.format(81),
getCommonCycle(x, y, z, cycle.retract, cycle.clearance),
feedOutput.format(F)
);
break;
case "counter-boring":
if (P > 0) {
writeBlock(
gRetractModal.format(98), gCycleModal.format(82),
getCommonCycle(x, y, z, cycle.retract, cycle.clearance),
"P" + milliFormat.format(P), // not optional
feedOutput.format(F)
);
} else {
writeBlock(
gRetractModal.format(98), gCycleModal.format(81),
getCommonCycle(x, y, z, cycle.retract, cycle.clearance),
feedOutput.format(F)
);
}
break;
case "chip-breaking":
if ((cycle.accumulatedDepth < cycle.depth) && (cycle.incrementalDepthReduction > 0)) {
expandCyclePoint(x, y, z);
} else if (cycle.accumulatedDepth < cycle.depth) {
writeBlock(
gRetractModal.format(98), gCycleModal.format(73),
getCommonCycle(x, y, z, cycle.retract, cycle.clearance),
("Q" + xyzFormat.format(cycle.incrementalDepth)),
("K" + xyzFormat.format(cycle.accumulatedDepth)),
conditional(P > 0, "P" + milliFormat.format(P)), // optional
feedOutput.format(F)
);
} else {
writeBlock(
gRetractModal.format(98), gCycleModal.format(73),
getCommonCycle(x, y, z, cycle.retract, cycle.clearance),
(((cycle.incrementalDepthReduction > 0) ? "I" : "Q") + xyzFormat.format(cycle.incrementalDepth)),
conditional(cycle.incrementalDepthReduction > 0, "J" + xyzFormat.format(cycle.incrementalDepthReduction)),
conditional(cycle.incrementalDepthReduction > 0, "K" + xyzFormat.format(cycle.minimumIncrementalDepth)),
conditional(P > 0, "P" + milliFormat.format(P)), // optional
feedOutput.format(F)
);
}
break;
case "deep-drilling":
writeBlock(
gRetractModal.format(98), gCycleModal.format(83),
getCommonCycle(x, y, z, cycle.retract, cycle.clearance),
(((cycle.incrementalDepthReduction > 0) ? "I" : "Q") + xyzFormat.format(cycle.incrementalDepth)),
conditional(cycle.incrementalDepthReduction > 0, "J" + xyzFormat.format(cycle.incrementalDepthReduction)),
conditional(cycle.incrementalDepthReduction > 0, "K" + xyzFormat.format(cycle.minimumIncrementalDepth)),
conditional(P > 0, "P" + milliFormat.format(P)), // optional
feedOutput.format(F)
);
break;
case "tapping":
var tappingFPM = tool.getThreadPitch() * rpmFormat.getResultingValue(spindleSpeed);
F = (getProperty("useG95forTapping") ? tool.getThreadPitch() : tappingFPM);
if (getProperty("useG95forTapping")) {
writeBlock(gFeedModeModal.format(95));
}
writeBlock(
gRetractModal.format(98), gCycleModal.format((tool.type == TOOL_TAP_LEFT_HAND) ? 74 : 84),
getCommonCycle(x, y, z, cycle.retract, cycle.clearance),
pitchOutput.format(F)
);
forceFeed();
break;
case "left-tapping":
var tappingFPM = tool.getThreadPitch() * rpmFormat.getResultingValue(spindleSpeed);
F = (getProperty("useG95forTapping") ? tool.getThreadPitch() : tappingFPM);
if (getProperty("useG95forTapping")) {
writeBlock(gFeedModeModal.format(95));
}
writeBlock(
gRetractModal.format(98), gCycleModal.format(74),
getCommonCycle(x, y, z, cycle.retract, cycle.clearance),
pitchOutput.format(F)
);
forceFeed();
break;
case "right-tapping":
var tappingFPM = tool.getThreadPitch() * rpmFormat.getResultingValue(spindleSpeed);
F = (getProperty("useG95forTapping") ? tool.getThreadPitch() : tappingFPM);
if (getProperty("useG95forTapping")) {
writeBlock(gFeedModeModal.format(95));
}
writeBlock(
gRetractModal.format(98), gCycleModal.format(84),
getCommonCycle(x, y, z, cycle.retract, cycle.clearance),
pitchOutput.format(F)
);
forceFeed();
break;
case "tapping-with-chip-breaking":
case "left-tapping-with-chip-breaking":
case "right-tapping-with-chip-breaking":
if (cycle.accumulatedDepth < cycle.depth) {
error(localize("Accumulated pecking depth is not supported for tapping cycles with chip breaking."));
return;
} else {
var tappingFPM = tool.getThreadPitch() * rpmFormat.getResultingValue(spindleSpeed);
F = (getProperty("useG95forTapping") ? tool.getThreadPitch() : tappingFPM);
if (getProperty("useG95forTapping")) {
writeBlock(gFeedModeModal.format(95));
}
if (getProperty("usePeckTapping")) {
writeBlock(
gRetractModal.format(98), gCycleModal.format((tool.type == TOOL_TAP_LEFT_HAND ? 74 : 84)),
getCommonCycle(x, y, z, cycle.retract, cycle.clearance),
peckOutput.format(cycle.incrementalDepth),
pitchOutput.format(F)
);
forceFeed();
} else {
// Parameter 57 bit 6, REPT RIG TAP, is set to 1 (On)
// On Mill software versions12.09 and above, REPT RIG TAP has been moved from the Parameters to Setting 133
var u = cycle.stock;
var step = cycle.incrementalDepth;
var first = true;
while (u > cycle.bottom) {
if (step < cycle.minimumIncrementalDepth) {
step = cycle.minimumIncrementalDepth;
}
u -= step;
step -= cycle.incrementalDepthReduction;
gCycleModal.reset(); // required
if ((u - 0.001) <= cycle.bottom) {
u = cycle.bottom;
}
if (first) {
first = false;
writeBlock(
gRetractModal.format(99), gCycleModal.format((tool.type == TOOL_TAP_LEFT_HAND ? 74 : 84)),
getCommonCycle((gPlaneModal.getCurrent() == 19) ? u : x, (gPlaneModal.getCurrent() == 18) ? u : y, (gPlaneModal.getCurrent() == 17) ? u : z, cycle.retract, cycle.clearance),
pitchOutput.format(F)
);
} else {
var position;
var depth;
switch (gPlaneModal.getCurrent()) {
case 17:
xOutput.reset();
position = xOutput.format(x);
depth = zOutput.format(u);
break;
case 18:
zOutput.reset();
position = zOutput.format(z);
depth = yOutput.format(u);
break;
case 19:
yOutput.reset();
position = yOutput.format(y);
depth = xOutput.format(u);
break;
}
writeBlock(conditional(u <= cycle.bottom, gRetractModal.format(98)), position, depth);
}
if (incrementalMode) {
setCyclePosition(cycle.retract);
}
}
}
}
forceFeed();
break;
case "fine-boring":
writeBlock(
gRetractModal.format(98), gCycleModal.format(76),
getCommonCycle(x, y, z, cycle.retract, cycle.clearance),
"P" + milliFormat.format(P), // not optional
"Q" + xyzFormat.format(cycle.shift),
feedOutput.format(F)
);
forceSpindleSpeed = true;
break;
case "back-boring":
if (P > 0) {
expandCyclePoint(x, y, z);
} else {
var dx = (gPlaneModal.getCurrent() == 19) ? cycle.backBoreDistance : 0;
var dy = (gPlaneModal.getCurrent() == 18) ? cycle.backBoreDistance : 0;
var dz = (gPlaneModal.getCurrent() == 17) ? cycle.backBoreDistance : 0;
writeBlock(
gRetractModal.format(98), gCycleModal.format(77),
getCommonCycle(x - dx, y - dy, z - dz, cycle.bottom, cycle.clearance),
"Q" + xyzFormat.format(cycle.shift),
feedOutput.format(F)
);
forceSpindleSpeed = true;
}
break;
case "reaming":
if (feedFormat.getResultingValue(cycle.feedrate) != feedFormat.getResultingValue(cycle.retractFeedrate)) {
expandCyclePoint(x, y, z);
break;
}
writeBlock(
gRetractModal.format(98), gCycleModal.format(85),
getCommonCycle(x, y, z, cycle.retract, cycle.clearance),
feedOutput.format(F)
);
break;
case "stop-boring":
if (P > 0) {
expandCyclePoint(x, y, z);
} else {
writeBlock(
gRetractModal.format(98), gCycleModal.format(86),
getCommonCycle(x, y, z, cycle.retract, cycle.clearance),
feedOutput.format(F)
);
forceSpindleSpeed = true;
}
break;
case "manual-boring":
writeBlock(
gRetractModal.format(98), gCycleModal.format(88),
getCommonCycle(x, y, z, cycle.retract, cycle.clearance),
"P" + milliFormat.format(P), // not optional
feedOutput.format(F)
);
break;
case "boring":
if (feedFormat.getResultingValue(cycle.feedrate) != feedFormat.getResultingValue(cycle.retractFeedrate)) {
expandCyclePoint(x, y, z);
break;
}
writeBlock(
gRetractModal.format(98), gCycleModal.format(89),
getCommonCycle(x, y, z, cycle.retract, cycle.clearance),
"P" + milliFormat.format(P), // not optional
feedOutput.format(F)
);
break;
case "probing-x":
protectedProbeMove(cycle, x, y, z - cycle.depth);
writeBlock(
gFormat.format(65), "P" + 9811,
"X" + xyzFormat.format(x + approach(cycle.approach1) * (cycle.probeClearance + tool.diameter / 2)),
"Q" + xyzFormat.format(cycle.probeOvertravel),
getProbingArguments(cycle, true)
);
break;
case "probing-y":
protectedProbeMove(cycle, x, y, z - cycle.depth);
writeBlock(
gFormat.format(65), "P" + 9811,
"Y" + xyzFormat.format(y + approach(cycle.approach1) * (cycle.probeClearance + tool.diameter / 2)),
"Q" + xyzFormat.format(cycle.probeOvertravel),
getProbingArguments(cycle, true)
);
break;
case "probing-z":
protectedProbeMove(cycle, x, y, Math.min(z - cycle.depth + cycle.probeClearance, cycle.retract));
writeBlock(
gFormat.format(65), "P" + 9811,
"Z" + xyzFormat.format(z - cycle.depth),
"Q" + xyzFormat.format(cycle.probeOvertravel),
getProbingArguments(cycle, true)
);
break;
case "probing-x-wall":
protectedProbeMove(cycle, x, y, z);
writeBlock(
gFormat.format(65), "P" + 9812,
"X" + xyzFormat.format(cycle.width1),
"Z" + xyzFormat.format(z - cycle.depth),
"Q" + xyzFormat.format(cycle.probeOvertravel),
"R" + xyzFormat.format(cycle.probeClearance),
getProbingArguments(cycle, true)
);
break;
case "probing-y-wall":
protectedProbeMove(cycle, x, y, z);
writeBlock(
gFormat.format(65), "P" + 9812,
"Y" + xyzFormat.format(cycle.width1),
"Z" + xyzFormat.format(z - cycle.depth),
"Q" + xyzFormat.format(cycle.probeOvertravel),
"R" + xyzFormat.format(cycle.probeClearance),
getProbingArguments(cycle, true)
);
break;
case "probing-x-channel":
protectedProbeMove(cycle, x, y, z - cycle.depth);
writeBlock(
gFormat.format(65), "P" + 9812,
"X" + xyzFormat.format(cycle.width1),
"Q" + xyzFormat.format(cycle.probeOvertravel),
// not required "R" + xyzFormat.format(cycle.probeClearance),
getProbingArguments(cycle, true)
);
break;
case "probing-x-channel-with-island":
protectedProbeMove(cycle, x, y, z);
writeBlock(
gFormat.format(65), "P" + 9812,
"X" + xyzFormat.format(cycle.width1),
"Z" + xyzFormat.format(z - cycle.depth),
"Q" + xyzFormat.format(cycle.probeOvertravel),
"R" + xyzFormat.format(-cycle.probeClearance),
getProbingArguments(cycle, true)
);
break;
case "probing-y-channel":
protectedProbeMove(cycle, x, y, z - cycle.depth);
writeBlock(
gFormat.format(65), "P" + 9812,
"Y" + xyzFormat.format(cycle.width1),
"Q" + xyzFormat.format(cycle.probeOvertravel),
// not required "R" + xyzFormat.format(cycle.probeClearance),
getProbingArguments(cycle, true)
);
break;
case "probing-y-channel-with-island":
protectedProbeMove(cycle, x, y, z);
writeBlock(
gFormat.format(65), "P" + 9812,
"Y" + xyzFormat.format(cycle.width1),
"Z" + xyzFormat.format(z - cycle.depth),
"Q" + xyzFormat.format(cycle.probeOvertravel),
"R" + xyzFormat.format(-cycle.probeClearance),
getProbingArguments(cycle, true)
);
break;
case "probing-xy-circular-boss":
protectedProbeMove(cycle, x, y, z);
writeBlock(
gFormat.format(65), "P" + 9814,
"D" + xyzFormat.format(cycle.width1),
"Z" + xyzFormat.format(z - cycle.depth),
"Q" + xyzFormat.format(cycle.probeOvertravel),
"R" + xyzFormat.format(cycle.probeClearance),
getProbingArguments(cycle, true)
);
break;
case "probing-xy-circular-partial-boss":
protectedProbeMove(cycle, x, y, z);
writeBlock(
gFormat.format(65), "P" + 9823,
"A" + xyzFormat.format(cycle.partialCircleAngleA),
"B" + xyzFormat.format(cycle.partialCircleAngleB),
"C" + xyzFormat.format(cycle.partialCircleAngleC),
"D" + xyzFormat.format(cycle.width1),
"Z" + xyzFormat.format(z - cycle.depth),
"Q" + xyzFormat.format(cycle.probeOvertravel),
"R" + xyzFormat.format(cycle.probeClearance),
getProbingArguments(cycle, true)
);
break;
case "probing-xy-circular-hole":
protectedProbeMove(cycle, x, y, z - cycle.depth);
writeBlock(
gFormat.format(65), "P" + 9814,
"D" + xyzFormat.format(cycle.width1),
"Q" + xyzFormat.format(cycle.probeOvertravel),
// not required "R" + xyzFormat.format(cycle.probeClearance),
getProbingArguments(cycle, true)
);
break;
case "probing-xy-circular-partial-hole":
protectedProbeMove(cycle, x, y, z - cycle.depth);
writeBlock(
gFormat.format(65), "P" + 9823,
"A" + xyzFormat.format(cycle.partialCircleAngleA),
"B" + xyzFormat.format(cycle.partialCircleAngleB),
"C" + xyzFormat.format(cycle.partialCircleAngleC),
"D" + xyzFormat.format(cycle.width1),
"Q" + xyzFormat.format(cycle.probeOvertravel),
getProbingArguments(cycle, true)
);
break;
case "probing-xy-circular-hole-with-island":
protectedProbeMove(cycle, x, y, z);
writeBlock(
gFormat.format(65), "P" + 9814,
"Z" + xyzFormat.format(z - cycle.depth),
"D" + xyzFormat.format(cycle.width1),
"Q" + xyzFormat.format(cycle.probeOvertravel),
"R" + xyzFormat.format(-cycle.probeClearance),
getProbingArguments(cycle, true)
);
break;
case "probing-xy-circular-partial-hole-with-island":
protectedProbeMove(cycle, x, y, z);
writeBlock(
gFormat.format(65), "P" + 9823,
"Z" + xyzFormat.format(z - cycle.depth),
"A" + xyzFormat.format(cycle.partialCircleAngleA),
"B" + xyzFormat.format(cycle.partialCircleAngleB),
"C" + xyzFormat.format(cycle.partialCircleAngleC),
"D" + xyzFormat.format(cycle.width1),
"Q" + xyzFormat.format(cycle.probeOvertravel),
"R" + xyzFormat.format(-cycle.probeClearance),
getProbingArguments(cycle, true)
);
break;
case "probing-xy-rectangular-hole":
protectedProbeMove(cycle, x, y, z - cycle.depth);
writeBlock(
gFormat.format(65), "P" + 9812,
"X" + xyzFormat.format(cycle.width1),
"Q" + xyzFormat.format(cycle.probeOvertravel),
// not required "R" + xyzFormat.format(-cycle.probeClearance),
getProbingArguments(cycle, true)
);
writeBlock(
gFormat.format(65), "P" + 9812,
"Y" + xyzFormat.format(cycle.width2),
"Q" + xyzFormat.format(cycle.probeOvertravel),
// not required "R" + xyzFormat.format(-cycle.probeClearance),
getProbingArguments(cycle, true)
);
break;
case "probing-xy-rectangular-boss":
protectedProbeMove(cycle, x, y, z);
writeBlock(
gFormat.format(65), "P" + 9812,
"Z" + xyzFormat.format(z - cycle.depth),
"X" + xyzFormat.format(cycle.width1),
"R" + xyzFormat.format(cycle.probeClearance),
"Q" + xyzFormat.format(cycle.probeOvertravel),
getProbingArguments(cycle, true)
);
writeBlock(
gFormat.format(65), "P" + 9812,
"Z" + xyzFormat.format(z - cycle.depth),
"Y" + xyzFormat.format(cycle.width2),
"R" + xyzFormat.format(cycle.probeClearance),
"Q" + xyzFormat.format(cycle.probeOvertravel),
getProbingArguments(cycle, true)
);
break;
case "probing-xy-rectangular-hole-with-island":
protectedProbeMove(cycle, x, y, z);
writeBlock(
gFormat.format(65), "P" + 9812,
"Z" + xyzFormat.format(z - cycle.depth),
"X" + xyzFormat.format(cycle.width1),
"Q" + xyzFormat.format(cycle.probeOvertravel),
"R" + xyzFormat.format(-cycle.probeClearance),
getProbingArguments(cycle, true)
);
writeBlock(
gFormat.format(65), "P" + 9812,
"Z" + xyzFormat.format(z - cycle.depth),
"Y" + xyzFormat.format(cycle.width2),
"Q" + xyzFormat.format(cycle.probeOvertravel),
"R" + xyzFormat.format(-cycle.probeClearance),
getProbingArguments(cycle, true)
);
break;
case "probing-xy-inner-corner":
var cornerX = x + approach(cycle.approach1) * (cycle.probeClearance + tool.diameter / 2);
var cornerY = y + approach(cycle.approach2) * (cycle.probeClearance + tool.diameter / 2);
var cornerI = 0;
var cornerJ = 0;
if (cycle.probeSpacing !== undefined) {
cornerI = cycle.probeSpacing;
cornerJ = cycle.probeSpacing;
}
if ((cornerI != 0) && (cornerJ != 0)) {
if (currentSection.strategy == "probe") {
setProbeAngleMethod();
probeVariables.compensationXY = "X[#185] Y[#186]";
}
}
protectedProbeMove(cycle, x, y, z - cycle.depth);
writeBlock(
gFormat.format(65), "P" + 9815, xOutput.format(cornerX), yOutput.format(cornerY),
conditional(cornerI != 0, "I" + xyzFormat.format(cornerI)),
conditional(cornerJ != 0, "J" + xyzFormat.format(cornerJ)),
"Q" + xyzFormat.format(cycle.probeOvertravel),
getProbingArguments(cycle, true)
);
break;
case "probing-xy-outer-corner":
var cornerX = x + approach(cycle.approach1) * (cycle.probeClearance + tool.diameter / 2);
var cornerY = y + approach(cycle.approach2) * (cycle.probeClearance + tool.diameter / 2);
var cornerI = 0;
var cornerJ = 0;
if (cycle.probeSpacing !== undefined) {
cornerI = cycle.probeSpacing;
cornerJ = cycle.probeSpacing;
}
if ((cornerI != 0) && (cornerJ != 0)) {
if (currentSection.strategy == "probe") {
setProbeAngleMethod();
probeVariables.compensationXY = "X[#185] Y[#186]";
}
}
protectedProbeMove(cycle, x, y, z - cycle.depth);
writeBlock(
gFormat.format(65), "P" + 9816, xOutput.format(cornerX), yOutput.format(cornerY),
conditional(cornerI != 0, "I" + xyzFormat.format(cornerI)),
conditional(cornerJ != 0, "J" + xyzFormat.format(cornerJ)),
"Q" + xyzFormat.format(cycle.probeOvertravel),
getProbingArguments(cycle, true)
);
break;
case "probing-x-plane-angle":
protectedProbeMove(cycle, x, y, z - cycle.depth);
writeBlock(
gFormat.format(65), "P" + 9843,
"X" + xyzFormat.format(x + approach(cycle.approach1) * (cycle.probeClearance + tool.diameter / 2)),
"D" + xyzFormat.format(cycle.probeSpacing),
"Q" + xyzFormat.format(cycle.probeOvertravel),
"A" + xyzFormat.format(cycle.nominalAngle != undefined ? cycle.nominalAngle : 90),
getProbingArguments(cycle, false)
);
if (currentSection.strategy == "probe") {
setProbeAngleMethod();
probeVariables.compensationXY = "X" + xyzFormat.format(0) + " Y" + xyzFormat.format(0);
}
break;
case "probing-y-plane-angle":
protectedProbeMove(cycle, x, y, z - cycle.depth);
writeBlock(
gFormat.format(65), "P" + 9843,
"Y" + xyzFormat.format(y + approach(cycle.approach1) * (cycle.probeClearance + tool.diameter / 2)),
"D" + xyzFormat.format(cycle.probeSpacing),
"Q" + xyzFormat.format(cycle.probeOvertravel),
"A" + xyzFormat.format(cycle.nominalAngle != undefined ? cycle.nominalAngle : 0),
getProbingArguments(cycle, false)
);
if (currentSection.strategy == "probe") {
setProbeAngleMethod();
probeVariables.compensationXY = "X" + xyzFormat.format(0) + " Y" + xyzFormat.format(0);
}
break;
case "probing-xy-pcd-hole":
protectedProbeMove(cycle, x, y, z);
writeBlock(
gFormat.format(65), "P" + 9819,
"A" + xyzFormat.format(cycle.pcdStartingAngle),
"B" + xyzFormat.format(cycle.numberOfSubfeatures),
"C" + xyzFormat.format(cycle.widthPCD),
"D" + xyzFormat.format(cycle.widthFeature),
"K" + xyzFormat.format(z - cycle.depth),
"Q" + xyzFormat.format(cycle.probeOvertravel),
getProbingArguments(cycle, false)
);
if (cycle.updateToolWear) {
error(localize("Action -Update Tool Wear- is not supported with this cycle"));
return;
}
break;
case "probing-xy-pcd-boss":
protectedProbeMove(cycle, x, y, z);
writeBlock(
gFormat.format(65), "P" + 9819,
"A" + xyzFormat.format(cycle.pcdStartingAngle),
"B" + xyzFormat.format(cycle.numberOfSubfeatures),
"C" + xyzFormat.format(cycle.widthPCD),
"D" + xyzFormat.format(cycle.widthFeature),
"Z" + xyzFormat.format(z - cycle.depth),
"Q" + xyzFormat.format(cycle.probeOvertravel),
"R" + xyzFormat.format(cycle.probeClearance),
getProbingArguments(cycle, false)
);
if (cycle.updateToolWear) {
error(localize("Action -Update Tool Wear- is not supported with this cycle"));
return;
}
break;
default:
expandCyclePoint(x, y, z);
}
// place cycle operation in subprogram
if (cycleSubprogramIsActive) {
if (forceCycle || cycleExpanded || isProbeOperation()) {
cycleSubprogramIsActive = false;
} else {
// call subprogram
writeBlock(mFormat.format(97), "P" + nFormat.format(currentSubprogram));
subprogramStart(new Vector(x, y, z), new Vector(0, 0, 0), false);
}
}
if (incrementalMode) { // set current position to clearance height
setCyclePosition(cycle.clearance);
}
// 2nd through nth cycle point
} else {
if (cycleExpanded) {
expandCyclePoint(x, y, z);
} else {
var _x;
var _y;
var _z;
if (!xyzFormat.areDifferent(x, xOutput.getCurrent()) &&
!xyzFormat.areDifferent(y, yOutput.getCurrent()) &&
!xyzFormat.areDifferent(z, zOutput.getCurrent())) {
switch (gPlaneModal.getCurrent()) {
case 17: // XY
xOutput.reset(); // at least one axis is required
break;
case 18: // ZX
zOutput.reset(); // at least one axis is required
break;
case 19: // YZ
yOutput.reset(); // at least one axis is required
break;
}
}
if (incrementalMode) { // set current position to retract height
setCyclePosition(cycle.retract);
}
writeBlock(xOutput.format(x), yOutput.format(y), zOutput.format(z));
if (incrementalMode) { // set current position to clearance height
setCyclePosition(cycle.clearance);
}
}
}
}
function getProbingArguments(cycle, updateWCS) {
var outputWCSCode = updateWCS && currentSection.strategy == "probe";
var probeOutputWorkOffset = currentSection.probeWorkOffset;
if (outputWCSCode) {
validate(
probeOutputWorkOffset > 0 && (probeOutputWorkOffset > 6 ? probeOutputWorkOffset - 6 : probeOutputWorkOffset) <= 99,
"Work offset is out of range."
);
var nextWorkOffset = hasNextSection() ? getNextSection().workOffset == 0 ? 1 : getNextSection().workOffset : -1;
if (probeOutputWorkOffset == nextWorkOffset) {
currentWorkOffset = undefined;
}
}
return [
(cycle.angleAskewAction == "stop-message" ? "B" + xyzFormat.format(cycle.toleranceAngle ? cycle.toleranceAngle : 0) : undefined),
((cycle.updateToolWear && cycle.toolWearErrorCorrection < 100) ? "F" + xyzFormat.format(cycle.toolWearErrorCorrection ? cycle.toolWearErrorCorrection / 100 : 100) : undefined),
(cycle.wrongSizeAction == "stop-message" ? "H" + xyzFormat.format(cycle.toleranceSize ? cycle.toleranceSize : 0) : undefined),
(cycle.outOfPositionAction == "stop-message" ? "M" + xyzFormat.format(cycle.tolerancePosition ? cycle.tolerancePosition : 0) : undefined),
((cycle.updateToolWear && cycleType == "probing-z") ? "T" + xyzFormat.format(cycle.toolLengthOffset) : undefined),
((cycle.updateToolWear && cycleType !== "probing-z") ? "T" + xyzFormat.format(cycle.toolDiameterOffset) : undefined),
(cycle.updateToolWear ? "V" + xyzFormat.format(cycle.toolWearUpdateThreshold ? cycle.toolWearUpdateThreshold : 0) : undefined),
(cycle.printResults ? "W" + xyzFormat.format(1 + cycle.incrementComponent) : undefined), // 1 for advance feature, 2 for reset feature count and advance component number. first reported result in a program should use W2.
conditional(outputWCSCode, (probeOutputWorkOffset > 6 ? probeExtWCSFormat.format((probeOutputWorkOffset - 6)) : probeWCSFormat.format(probeOutputWorkOffset)))
];
}
function onCycleEnd() {
if (isProbeOperation()) {
zOutput.reset();
gMotionModal.reset();
writeBlock(gFormat.format(65), "P" + 9810, zOutput.format(cycle.retract)); // protected retract move
} else {
if (cycleSubprogramIsActive) {
subprogramEnd();
cycleSubprogramIsActive = false;
}
if (!cycleExpanded || tapping) {
writeBlock(gCycleModal.format(80));
gMotionModal.reset();
feedOutput.reset();
}
writeBlock(gFeedModeModal.format(94));
if (currentSection.feedMode == FEED_PER_REVOLUTION) {
feedOutput.setFormat(feedFormat); // re-apply feedFormat to feedOutput
}
}
}
var pendingRadiusCompensation = -1;
function onRadiusCompensation() {
pendingRadiusCompensation = radiusCompensation;
}
function onRapid(_x, _y, _z) {
if (knuckleAdjustmentIsActive) {
knuckleRapid(_x, _y, _z);
return;
}
var x = xOutput.format(_x);
var y = yOutput.format(_y);
var z = zOutput.format(_z);
if (x || y || z) {
if (pendingRadiusCompensation >= 0) {
error(localize("Radius compensation mode cannot be changed at rapid traversal."));
return;
}
if (!getProperty("useG0") && (((x ? 1 : 0) + (y ? 1 : 0) + (z ? 1 : 0)) > 1)) {
// axes are not synchronized
writeBlock(gFeedModeModal.format(94), gMotionModal.format(1), x, y, z, getFeed(toPreciseUnit(highFeedrate, MM)));
} else {
writeBlock(gMotionModal.format(0), x, y, z);
forceFeed();
}
}
}
function onLinear(_x, _y, _z, feed) {
var c = "";
if (knuckleAdjustmentIsActive) {
c = knuckleLinear(_x, _y, _z, feed);
if (c == "false") {
return;
} else if ((getProperty("adjustKnuckleAngle") == "preposition") && c) {
writeBlock(gMotionModal.format(0), c);
c = "";
}
}
if (pendingRadiusCompensation >= 0) {
// ensure that we end at desired position when compensation is turned off
xOutput.reset();
yOutput.reset();
}
var x = xOutput.format(_x);
var y = yOutput.format(_y);
var z = zOutput.format(_z);
var f = getFeed(feed);
var fMode = currentSection.feedMode == FEED_PER_REVOLUTION ? 95 : 94;
if (x || y || z) {
if (pendingRadiusCompensation >= 0) {
pendingRadiusCompensation = -1;
var d = tool.diameterOffset;
if ((d > 200 && d < 1000) || d > 9999) {
warning(localize("Diameter offset out of range."));
}
writeBlock(gPlaneModal.format(17), gFeedModeModal.format(fMode));
switch (radiusCompensation) {
case RADIUS_COMPENSATION_LEFT:
dOutput.reset();
writeBlock(gMotionModal.format(1), gFormat.format(41), x, y, z, c, dOutput.format(d), f);
break;
case RADIUS_COMPENSATION_RIGHT:
dOutput.reset();
writeBlock(gMotionModal.format(1), gFormat.format(42), x, y, z, c, dOutput.format(d), f);
break;
default:
writeBlock(gMotionModal.format(1), gFormat.format(40), x, y, z, c, f);
}
} else {
writeBlock(gFeedModeModal.format(fMode), gMotionModal.format(1), x, y, z, c, f);
}
} else if (f) {
if (getNextRecord().isMotion()) { // try not to output feed without motion
forceFeed(); // force feed on next line
} else {
writeBlock(gMotionModal.format(1), f);
}
}
previousZ = _z;
}
function onRapid5D(_x, _y, _z, _a, _b, _c) {
if (!currentSection.isOptimizedForMachine()) {
error(localize("This post configuration has not been customized for 5-axis simultaneous toolpath."));
return;
}
if (pendingRadiusCompensation >= 0) {
error(localize("Radius compensation mode cannot be changed at rapid traversal."));
return;
}
var x = xOutput.format(_x);
var y = yOutput.format(_y);
var z = zOutput.format(_z);
var a = aOutput.format(_a);
var b = bOutput.format(_b);
var c = cOutput.format(_c);
if (x || y || z || a || b || c) {
var numLinear = (x ? 1 : 0) + (y ? 1 : 0) + (z ? 1 : 0);
var numRotary = (a ? 1 : 0) + (b ? 1 : 0) + (c ? 1 : 0);
if ((!getProperty("useG0") && numLinear > 1) || numRotary > 0 || operationSupportsTCP) { // required with rotary moves to maintain TCP
writeBlock(gMotionModal.format(1), x, y, z, a, b, c, getFeed(toPreciseUnit(highFeedrate, MM)));
} else {
writeBlock(gMotionModal.format(0), x, y, z, a, b, c);
forceFeed();
}
}
previousABCPosition = new Vector(_a, _b, _c);
}
function onLinear5D(_x, _y, _z, _a, _b, _c, feed) {
if (!currentSection.isOptimizedForMachine()) {
error(localize("This post configuration has not been customized for 5-axis simultaneous toolpath."));
return;
}
if (pendingRadiusCompensation >= 0) {
error(localize("Radius compensation cannot be activated/deactivated for 5-axis move."));
return;
}
var x = xOutput.format(_x);
var y = yOutput.format(_y);
var z = zOutput.format(_z);
var a = aOutput.format(_a);
var b = bOutput.format(_b);
var c = cOutput.format(_c);
var f = {};
f.frn = feedOutput.format(feed);
f.fmode = 94;
if (x || y || z || a || b || c) {
writeBlock(gFeedModeModal.format(f.fmode), gMotionModal.format(1), x, y, z, a, b, c, f.frn);
} else if (f.frn) {
if (getNextRecord().isMotion()) { // try not to output feed without motion
feedOutput.reset(); // force feed on next line
} else {
writeBlock(gFeedModeModal.format(f.fmode), gMotionModal.format(1), f.frn);
}
}
previousABCPosition = new Vector(_a, _b, _c);
}
// Start of automatic C-axis positioning logic
var knuckleFeed = toPreciseUnit(10, IN); // plunge feedrate during retract/reposition
var minimumKnuckleDistance = toPreciseUnit(0.2, IN); // distance along linear move to rotate C-axis
var safeKnuckleDistance = 0.2; // distance above part to retract when C-axis has to be repositioned
var previousKnuckleAngle = 0; // maintained by post
var previousZ; // maintained by post
var knuckleAdjustmentIsActive; // defined in onSection
var safeKnuckleClearance; // defined in onSection
var rapidMove; // rapid move buffering
var rapidDir;
var rapidIsBuffered = false;
var linearMove; // linear move buffering
var linearFeed;
var linearIsBuffered = false;
function getKnuckleAngle(start, end, center, plane, clockwise) {
var angle;
if (center != undefined) {
var endVec = Vector.diff(end, center).normalized;
var axis = plane == PLANE_ZX ? new Vector(0, 1, 0) : (plane == PLANE_YZ ? new Vector(1, 0, 0) : new Vector(0, 0, 1));
var fwdVec = clockwise ? Vector.cross(endVec, axis) : Vector.cross(axis, endVec);
angle = toRad(getProperty("baseKnuckleAngle")) - fwdVec.getXYAngle();
} else {
var fwdVec = Vector.diff(end, start).getNormalized();
if ((xyzFormat.getResultingValue(start.x) == xyzFormat.getResultingValue(end.x)) &&
(xyzFormat.getResultingValue(start.y) == xyzFormat.getResultingValue(end.y))) {
angle = previousKnuckleAngle;
} else {
angle = toRad(getProperty("baseKnuckleAngle")) - fwdVec.getXYAngle();
}
}
return checkKnuckleAngle(angle, true, true);
}
function checkKnuckleAngle(angle, output, reposition) {
//writeDebug("angle = " + abcFormat.format(angle));
//writeDebug("previous = " + abcFormat.format(previousKnuckleAngle));
var diff = angle - previousKnuckleAngle;
var i = 0;
while (true) {
if (diff > Math.PI) {
diff -= Math.PI * 2;
} else if (diff < -Math.PI) {
diff += Math.PI * 2;
} else {
break;
}
i++;
if (i == 10) {
error(localize("Cannot calculate C-axis angle"));
return "";
}
}
angle = toRad(abcFormat.getResultingValue(previousKnuckleAngle + diff));
angle = (angle < machineConfiguration.getAxisV().getRange().minimum) ? angle + (Math.PI * 2) : angle;
angle = (angle > machineConfiguration.getAxisV().getRange().maximum) ? angle - (Math.PI * 2) : angle;
diff = angle - previousKnuckleAngle;
if (reposition) {
if (!repositionKnuckle(angle, diff, false)) {
return "";
}
}
if (output) {
var c = cOutput.format(angle);
previousKnuckleAngle = angle;
return c;
}
return "";
}
function repositionKnuckle(angle, diff, force) {
if (force || ((abcFormat.getResultingValue(Math.abs(diff)) > 180) && !rapidIsBuffered)) {
if (force) {
cOutput.reset();
}
var comment = force ? "" : formatComment("Reposition Head");
switch (getProperty("adjustKnuckleAngle")) {
case "staydown":
var c = cOutput.format(angle);
writeBlock(gMotionModal.format(1), c, getFeed(toPreciseUnit(highFeedrate, MM)), comment);
break;
case "retract":
var c = cOutput.format(angle);
writeBlock(gMotionModal.format(1), zOutput.format(safeKnuckleClearance), getFeed(toPreciseUnit(highFeedrate, MM)));
writeBlock(gMotionModal.format(1), c, getFeed(toPreciseUnit(highFeedrate, MM)), comment);
writeBlock(gMotionModal.format(1), zOutput.format(getCurrentPosition().z), feedOutput.format(knuckleFeed));
break;
case "lock":
return false;
}
}
return true;
}
function knuckleRapid(_x, _y, _z) {
flushRapid("");
previousKnuckleAngle = 0;
rapidMove = new Vector(_x, _y, _z);
rapidDir = Vector.diff(rapidMove, getCurrentPosition()).normalized;
rapidIsBuffered = true;
if (!getNextRecord().isMotion()) {
flushRapid("");
}
}
function flushRapid(c) {
if (!rapidIsBuffered) {
return c;
}
// writeDebug("buffered rapid");
var x = xOutput.format(rapidMove.x);
var y = yOutput.format(rapidMove.y);
var z = zOutput.format(rapidMove.z);
if (x || y || z) {
if ((getProperty("adjustKnuckleAngle") == "retract") && (previousZ < safeKnuckleClearance) && c) {
repositionKnuckle(previousKnuckleAngle, 0, true);
writeBlock(gMotionModal.format(1), x, y, z, feedOutput.format(toPreciseUnit(highFeedrate, MM)));
if (!z) {
writeBlock(gMotionModal.format(1), zOutput.format(previousZ), getFeed(toPreciseUnit(highFeedrate, MM))); // plunge back down in Z
}
} else {
writeBlock(gMotionModal.format(1), x, y, z, c, getFeed(toPreciseUnit(highFeedrate, MM)));
}
feedOutput.reset();
c = "";
}
previousZ = rapidMove.z;
rapidIsBuffered = false;
if (linearIsBuffered) {
//writeDebug("buffered linear");
var x = xOutput.format(linearMove.x);
var y = yOutput.format(linearMove.y);
var z = zOutput.format(linearMove.z);
if (x || y || z) {
writeBlock(gMotionModal.format(1), x, y, z, feedOutput.format(linearFeed));
feedOutput.reset();
}
previousZ = linearMove.z;
linearIsBuffered = false;
}
return c;
}
function knuckleLinear(_x, _y, _z, feed) {
var current = getCurrentPosition();
var end = new Vector(_x, _y, _z);
var fwd = Vector.diff(end, current).normalized;
if (isSameDirection(fwd, new Vector(0, 0, -1))) {
if (true) {
linearMove = end;
linearFeed = feed;
linearIsBuffered = true;
return "false";
}
}
var c = getKnuckleAngle(current, end);
c = flushRapid(c);
if ((getProperty("adjustKnuckleAngle") == "preposition") && c) {
writeBlock(gMotionModal.format(0), c);
c = "";
} else if (c) {
var dist = Vector.diff(current, end).length;
if (dist > minimumKnuckleDistance) {
var midpoint = Vector.sum(current, Vector.product(fwd, minimumKnuckleDistance));
writeBlock(gMotionModal.format(1), xOutput.format(midpoint.x), yOutput.format(midpoint.y), zOutput.format(midpoint.z), c, feedOutput.format(feed));
c = "";
}
}
return c;
}
function linearizeCircular(c, toler) {
if (c) {
cOutput.reset();
}
linearize(toler);
}
// End of automatic C-axis positioning logic
// Start of onRewindMachine logic
/** Allow user to override the onRewind logic. */
function onRewindMachineEntry(_a, _b, _c) {
return false;
}
/** Retract to safe position before indexing rotaries. */
var safeRetractPositionZ;
function onMoveToSafeRetractPosition() {
var position = getCurrentPosition();
var workpiece = getWorkpiece();
safeRetractPositionZ = workpiece.upper.z + getProperty("safeRetractDistanceZ");
writeRetractSafeZ(new Vector(position.x, position.y, safeRetractPositionZ), false, false, "", false);
if (getProperty("centerOnMultiAxis")) {
invokeOnRapid(
workpiece.lower.x + ((workpiece.upper.x - workpiece.lower.x) / 2),
workpiece.lower.y + ((workpiece.upper.y - workpiece.lower.y) / 2),
safeRetractPositionZ
);
}
}
/** Rotate axes to new position above reentry position */
function onRotateAxes(_x, _y, _z, _a, _b, _c) {
// position rotary axes
xOutput.disable();
yOutput.disable();
zOutput.disable();
if (typeof unwindABC == "function") {
unwindABC(new Vector(_a, _b, _c), false);
}
onLinear5D(_x, _y, _z, _a, _b, _c, highRotaryFeedrate);
setCurrentABC(new Vector(_a, _b, _c));
xOutput.enable();
yOutput.enable();
zOutput.enable();
}
/** Return from safe position after indexing rotaries. */
function onReturnFromSafeRetractPosition(_x, _y, _z) {
if (getProperty("centerOnMultiAxis")) {
invokeOnRapid(_x, _y, safeRetractPositionZ);
}
invokeOnRapid(_x, _y, _z);
}
// End of onRewindMachine logic
function onCircular(clockwise, cx, cy, cz, x, y, z, feed) {
if (isSpiral()) {
var startRadius = getCircularStartRadius();
var endRadius = getCircularRadius();
var dr = Math.abs(endRadius - startRadius);
if (dr > maximumCircularRadiiDifference) { // maximum limit
linearize(tolerance); // or alternatively use other G-codes for spiral motion
return;
}
}
if (pendingRadiusCompensation >= 0) {
error(localize("Radius compensation cannot be activated/deactivated for a circular move."));
return;
}
var start = getCurrentPosition();
var c = "";
if (knuckleAdjustmentIsActive && (getProperty("knuckleCircular") != "false")) {
c = getKnuckleAngle(start, new Vector(x, y, z), new Vector(cx, cy, cz), getCircularPlane(), clockwise);
c = flushRapid(c);
} else if (getProperty("knuckleCircular") == "false") {
linearize(tolerance);
return;
}
if (isFullCircle()) {
if (getProperty("useRadius") || isHelical()) { // radius mode does not support full arcs
linearizeCircular(c, tolerance);
return;
}
switch (getCircularPlane()) {
case PLANE_XY:
writeBlock(gPlaneModal.format(17), gMotionModal.format(clockwise ? 2 : 3), iOutput.format(cx - start.x), jOutput.format(cy - start.y), c, getFeed(feed));
break;
case PLANE_ZX:
if (activeDWO && machineConfiguration.isHeadConfiguration()) {
linearizeCircular(c, tolerance);
} else {
writeBlock(gPlaneModal.format(18), gMotionModal.format(clockwise ? 2 : 3), iOutput.format(cx - start.x), kOutput.format(cz - start.z), c, getFeed(feed));
}
break;
case PLANE_YZ:
if (activeDWO && machineConfiguration.isHeadConfiguration()) {
linearizeCircular(c, tolerance);
} else {
writeBlock(gPlaneModal.format(19), gMotionModal.format(clockwise ? 2 : 3), jOutput.format(cy - start.y), kOutput.format(cz - start.z), c, getFeed(feed));
}
break;
default:
linearizeCircular(c, tolerance);
}
} else if (!getProperty("useRadius")) {
switch (getCircularPlane()) {
case PLANE_XY:
writeBlock(gPlaneModal.format(17), gMotionModal.format(clockwise ? 2 : 3), xOutput.format(x), yOutput.format(y), zOutput.format(z), iOutput.format(cx - start.x), jOutput.format(cy - start.y), c, getFeed(feed));
break;
case PLANE_ZX:
if (activeDWO && machineConfiguration.isHeadConfiguration()) {
linearizeCircular(c, tolerance);
} else {
writeBlock(gPlaneModal.format(18), gMotionModal.format(clockwise ? 2 : 3), xOutput.format(x), yOutput.format(y), zOutput.format(z), iOutput.format(cx - start.x), kOutput.format(cz - start.z), c, getFeed(feed));
}
break;
case PLANE_YZ:
if (activeDWO && machineConfiguration.isHeadConfiguration()) {
linearizeCircular(c, tolerance);
} else {
writeBlock(gPlaneModal.format(19), gMotionModal.format(clockwise ? 2 : 3), xOutput.format(x), yOutput.format(y), zOutput.format(z), jOutput.format(cy - start.y), kOutput.format(cz - start.z), c, getFeed(feed));
}
break;
default:
linearizeCircular(c, tolerance);
}
} else { // use radius mode
var r = getCircularRadius();
if (toDeg(getCircularSweep()) > (180 + 1e-9)) {
r = -r; // allow up to <360 deg arcs
}
switch (getCircularPlane()) {
case PLANE_XY:
writeBlock(gPlaneModal.format(17), gMotionModal.format(clockwise ? 2 : 3), xOutput.format(x), yOutput.format(y), zOutput.format(z), c, "R" + rFormat.format(r), getFeed(feed));
break;
case PLANE_ZX:
if (activeDWO && machineConfiguration.isHeadConfiguration()) {
linearizeCircular(c, tolerance);
} else {
writeBlock(gPlaneModal.format(18), gMotionModal.format(clockwise ? 2 : 3), xOutput.format(x), yOutput.format(y), zOutput.format(z), c, "R" + rFormat.format(r), getFeed(feed));
}
break;
case PLANE_YZ:
if (activeDWO && machineConfiguration.isHeadConfiguration()) {
linearizeCircular(c, tolerance);
} else {
writeBlock(gPlaneModal.format(19), gMotionModal.format(clockwise ? 2 : 3), xOutput.format(x), yOutput.format(y), zOutput.format(z), c, "R" + rFormat.format(r), getFeed(feed));
}
break;
default:
linearizeCircular(c, tolerance);
}
}
}
var currentCoolantMode = COOLANT_OFF;
var coolantOff = undefined;
var forceCoolant = false;
var isOptionalCoolant = false;
var isSpecialCoolantActive = false;
function setCoolant(coolant) {
var coolantCodes = getCoolantCodes(coolant);
forceSingleLine = false;
currentCoolantPressure = coolant == COOLANT_FLOOD ? currentCoolantPressure : "";
if ((coolantCodes != undefined) && (coolant == COOLANT_FLOOD)) {
if (coolantPressure != "") {
forceSingleLine = true;
coolantCodes.push(coolantPressure);
}
currentCoolantPressure = coolantPressure;
}
if (Array.isArray(coolantCodes)) {
if (singleLineCoolant || forceSingleLine) {
skipBlock = isOptionalCoolant;
writeBlock(coolantCodes.join(getWordSeparator()));
} else {
for (var c in coolantCodes) {
skipBlock = isOptionalCoolant;
writeBlock(coolantCodes[c]);
}
}
return undefined;
}
return coolantCodes;
}
function getCoolantCodes(coolant) {
isOptionalCoolant = false;
var multipleCoolantBlocks = new Array(); // create a formatted array to be passed into the outputted line
if (!coolants) {
error(localize("Coolants have not been defined."));
}
if (tool.type == TOOL_PROBE) { // avoid coolant output for probing
coolant = COOLANT_OFF;
}
if (coolant == currentCoolantMode) {
if (operationNeedsSafeStart && coolant != COOLANT_OFF && !isSpecialCoolantActive) {
isOptionalCoolant = true;
} else if (!forceCoolant || coolant == COOLANT_OFF) {
return undefined; // coolant is already active
}
}
if ((coolant != COOLANT_OFF) && (currentCoolantMode != COOLANT_OFF) && (coolantOff != undefined) && !isOptionalCoolant && !forceCoolant) {
if (Array.isArray(coolantOff)) {
for (var i in coolantOff) {
multipleCoolantBlocks.push(coolantOff[i]);
}
} else {
multipleCoolantBlocks.push(coolantOff);
}
}
forceCoolant = false;
if (isSpecialCoolantActive) {
forceSpindleSpeed = true;
}
var m;
var coolantCodes = {};
for (var c in coolants) { // find required coolant codes into the coolants array
if (coolants[c].id == coolant) {
isSpecialCoolantActive = (coolants[c].id == COOLANT_THROUGH_TOOL) || (coolants[c].id == COOLANT_FLOOD_THROUGH_TOOL) || (coolants[c].id == COOLANT_AIR_THROUGH_TOOL);
coolantCodes.on = coolants[c].on;
if (coolants[c].off != undefined) {
coolantCodes.off = coolants[c].off;
break;
} else {
for (var i in coolants) {
if (coolants[i].id == COOLANT_OFF) {
coolantCodes.off = coolants[i].off;
break;
}
}
}
}
}
if (coolant == COOLANT_OFF) {
m = !coolantOff ? coolantCodes.off : coolantOff; // use the default coolant off command when an 'off' value is not specified
} else {
coolantOff = coolantCodes.off;
m = coolantCodes.on;
}
if (!m) {
onUnsupportedCoolant(coolant);
m = 9;
} else {
if (Array.isArray(m)) {
for (var i in m) {
multipleCoolantBlocks.push(m[i]);
}
} else {
multipleCoolantBlocks.push(m);
}
currentCoolantMode = coolant;
for (var i in multipleCoolantBlocks) {
if (typeof multipleCoolantBlocks[i] == "number") {
multipleCoolantBlocks[i] = mFormat.format(multipleCoolantBlocks[i]);
}
}
return multipleCoolantBlocks; // return the single formatted coolant value
}
return undefined;
}
var mapCommand = {
COMMAND_END : 2,
COMMAND_SPINDLE_CLOCKWISE : 3,
COMMAND_SPINDLE_COUNTERCLOCKWISE: 4,
COMMAND_STOP_SPINDLE : 5,
COMMAND_ORIENTATE_SPINDLE : 19,
COMMAND_LOAD_TOOL : 6
};
function onCommand(command) {
switch (command) {
case COMMAND_STOP:
writeBlock(mFormat.format(0));
forceSpindleSpeed = true;
forceCoolant = true;
return;
case COMMAND_OPTIONAL_STOP:
writeBlock(mFormat.format(1));
forceSpindleSpeed = true;
forceCoolant = true;
return;
case COMMAND_COOLANT_ON:
setCoolant(COOLANT_FLOOD);
return;
case COMMAND_COOLANT_OFF:
setCoolant(COOLANT_OFF);
return;
case COMMAND_START_SPINDLE:
onCommand(tool.clockwise ? COMMAND_SPINDLE_CLOCKWISE : COMMAND_SPINDLE_COUNTERCLOCKWISE);
return;
case COMMAND_LOCK_MULTI_AXIS:
if (axisIsClamped && !operationNeedsSafeStart) {
return;
}
var outputClampCodes = getProperty("useClampCodes") || currentSection.isMultiAxis();
if (outputClampCodes && machineConfiguration.isMultiAxisConfiguration() && (machineConfiguration.getNumberOfAxes() >= 4)) {
var _skipBlock = skipBlock;
writeBlock(mClampModal.format(10)); // lock 4th-axis motion
if (machineConfiguration.getNumberOfAxes() == 5) {
skipBlock = _skipBlock;
writeBlock(mClampModal.format(12)); // lock 5th-axis motion
}
}
axisIsClamped = true;
return;
case COMMAND_UNLOCK_MULTI_AXIS:
if (!axisIsClamped && !operationNeedsSafeStart) {
return;
}
if (machineConfiguration.isMultiAxisConfiguration() && (machineConfiguration.getNumberOfAxes() >= 4)) {
var _skipBlock = skipBlock;
writeBlock(mClampModal.format(11)); // unlock 4th-axis motion
if (machineConfiguration.getNumberOfAxes() == 5) {
skipBlock = _skipBlock;
writeBlock(mClampModal.format(13)); // unlock 5th-axis motion
}
}
axisIsClamped = false;
return;
case COMMAND_BREAK_CONTROL:
if (!toolChecked) { // avoid duplicate COMMAND_BREAK_CONTROL
prepareForToolCheck();
writeBlock(
gFormat.format(65),
"P" + 9853,
"T" + toolFormat.format(tool.number),
"B" + xyzFormat.format(0),
"H" + xyzFormat.format(getProperty("toolBreakageTolerance"))
);
toolChecked = true;
lengthCompensationActive = false; // macro 9853 cancels tool length compensation
}
return;
case COMMAND_TOOL_MEASURE:
measureTool = true;
return;
case COMMAND_START_CHIP_TRANSPORT:
// writeBlock(mFormat.format(31));
return;
case COMMAND_STOP_CHIP_TRANSPORT:
// writeBlock(mFormat.format(33));
return;
case COMMAND_PROBE_ON:
return;
case COMMAND_PROBE_OFF:
return;
}
var stringId = getCommandStringId(command);
var mcode = mapCommand[stringId];
if (mcode != undefined) {
writeBlock(mFormat.format(mcode));
} else {
onUnsupportedCommand(command);
}
}
var toolChecked = false; // specifies that the tool has been checked with the probe
function onSectionEnd() {
if (typeof inspectionProcessSectionEnd == "function") {
inspectionProcessSectionEnd();
}
if (!isLastSection() && (getNextSection().getTool().coolant != tool.coolant)) {
setCoolant(COOLANT_OFF);
}
if ((((getCurrentSectionId() + 1) >= getNumberOfSections()) ||
(tool.number != getNextSection().getTool().number)) &&
tool.breakControl) {
onCommand(COMMAND_BREAK_CONTROL);
} else {
toolChecked = false;
}
if (true) {
if (isRedirecting()) {
if (firstPattern) {
var finalPosition = getFramePosition(currentSection.getFinalPosition());
var abc;
if (currentSection.isMultiAxis() && machineConfiguration.isMultiAxisConfiguration()) {
abc = currentSection.getFinalToolAxisABC();
} else {
abc = currentWorkPlaneABC;
}
if (abc == undefined) {
abc = new Vector(0, 0, 0);
}
setAbsIncMode(false, finalPosition, abc);
subprogramEnd();
}
}
}
if (getProperty("safeStartAllOperations")) {
forceAny();
} else { // don't force rotaries between 3D operations
forceXYZ();
forceFeed();
}
if (isProbeOperation()) {
writeBlock(gFormat.format(65), "P" + 9833); // spin the probe off
if (probeVariables.probeAngleMethod != "G68") {
setProbeAngle(); // output probe angle rotations if required
}
}
operationNeedsSafeStart = false; // reset for next section
// the code below gets the machine angles from previous operation. closestABC must also be set to true
if (currentSection.isMultiAxis() && currentSection.isOptimizedForMachine()) {
currentMachineABC = currentSection.getFinalToolAxisABC();
}
writeBlock(gFeedModeModal.format(94)); // feed per minute
if (currentSection.isMultiAxis()) {
if (hasNextSection() && !getNextSection().isMultiAxis()) {
onCommand(COMMAND_LOCK_MULTI_AXIS);
}
}
// reset for next section
coolantPressure = "";
}
/** Output block to do safe retract in Z for head machine. */
function writeRetractSafeZ(position, enableComp, forceTCP, comment, forceRetract) {
if (!retracted || forceRetract) {
var lengthOffset = tool.lengthOffset;
var workpiece = getWorkpiece();
var clearance = workpiece.upper.z + getProperty("safeRetractDistanceZ");
if ((clearance > getCurrentPosition().z) || enableComp || forceRetract) {
if (typeof position != "number") {
forceXYZ();
writeBlock(
gMotionModal.format(0),
conditional(enableComp, gFormat.format((currentSection.isMultiAxis() || forceTCP || knuckleAdjustmentIsActive) ? 234 : 43)),
xOutput.format(position.x),
yOutput.format(position.y),
zOutput.format(position.z),
conditional(enableComp, hFormat.format(lengthOffset)),
conditional(comment, formatComment(comment))
);
} else {
zOutput.reset();
writeBlock(
gMotionModal.format(0),
conditional(enableComp, gFormat.format((currentSection.isMultiAxis() || forceTCP || knuckleAdjustmentIsActive) ? 234 : 43)),
zOutput.format(position),
conditional(enableComp, hFormat.format(lengthOffset)),
conditional(comment, formatComment(comment))
);
}
feedOutput.reset();
}
lengthCompensationActive = enableComp ? true : lengthCompensationActive;
// optional move to safe XY - not implemented
}
}
/** Calculates the retract plane based on the B-axis position. */
var baseRetractDiameter = toPreciseUnit(3, IN); // minimum tool diameter for retract plane calculations
var baseRetractPosition = toPreciseUnit(-13.5, IN); // upper retract limit with B90
function calculateRetractPlane(_abc) {
// retract to full height
if (!adjustRetractHeight) {
return machineConfiguration.getRetractPlane();
}
var radius = Math.max(tool.diameter, baseRetractDiameter) / 2;
var retractPosition = baseRetractPosition - (radius - (baseRetractDiameter / 2));
var b = Math.abs(_abc.y);
var minAngle = toRad(42); // minumum angle to consider for adjustment
var plane = 0;
if (b > minAngle) {
var max = toRad(90) - minAngle;
var delta = b - minAngle;
plane = (delta / max) * retractPosition;
}
// var plane = Math.sin(Math.abs(_abc.y) - minAngle) * retractPosition;
return (plane < machineConfiguration.getRetractPlane()) ? plane : machineConfiguration.getRetractPlane();
}
/** Output block to do safe retract and/or move to home position. */
function writeRetract() {
// initialize routine
var _xyzMoved = new Array(false, false, false);
var _useG28 = getProperty("useG28"); // can be either true or false
var _skipBlock = skipBlock;
// check syntax of call
if (arguments.length == 0) {
error(localize("No axis specified for writeRetract()."));
return;
}
for (var i = 0; i < arguments.length; ++i) {
if ((arguments[i] < 0) || (arguments[i] > 2)) {
error(localize("Bad axis specified for writeRetract()."));
return;
}
if (_xyzMoved[arguments[i]]) {
error(localize("Cannot retract the same axis twice in one line"));
return;
}
_xyzMoved[arguments[i]] = true;
}
// special conditions
if (_useG28 && _xyzMoved[2] && (_xyzMoved[0] || _xyzMoved[1])) { // XY don't use G28
error(localize("You cannot move home in XY & Z in the same block."));
return;
}
if (_xyzMoved[0] || _xyzMoved[1]) {
_useG28 = false;
}
cancelG68Rotation(); // G68 has to be canceled for retracts
var retractPlane = calculateRetractPlane(previousABCPosition); // calculate safe retract height
// define home positions
var _xHome;
var _yHome;
var _zHome;
if (_useG28) {
_xHome = 0;
_yHome = 0;
_zHome = 0;
} else {
_xHome = machineConfiguration.hasHomePositionX() ? machineConfiguration.getHomePositionX() : 0;
_yHome = machineConfiguration.hasHomePositionY() ? machineConfiguration.getHomePositionY() : 0;
_zHome = retractPlane;
}
// format home positions
var words = []; // store all retracted axes in an array
for (var i = 0; i < arguments.length; ++i) {
// define the axes to move
switch (arguments[i]) {
case X:
words.push("X" + xyzFormat.format(_xHome));
break;
case Y:
words.push("Y" + xyzFormat.format(_yHome));
break;
case Z:
skipBlock = _skipBlock;
cancelWorkPlane();
skipBlock = _skipBlock;
disableLengthCompensation(false);
skipBlock = _skipBlock;
words.push("Z" + xyzFormat.format(_zHome));
retracted = !skipBlock;
currentRetractPlane = _zHome;
break;
}
}
// output move to home
if (words.length > 0) {
if (_useG28) {
gAbsIncModal.reset();
writeBlock(gFormat.format(28), gAbsIncModal.format(91), words);
writeBlock(gAbsIncModal.format(90));
} else {
gMotionModal.reset();
writeBlock(gAbsIncModal.format(90), gFormat.format(53), gMotionModal.format(0), words);
}
cancelWorkPlane();
if (_xyzMoved[2]) { // reset head when retracted
var a = aOutput.format(0);
var b = bOutput.format(0);
var c = cOutput.format(0);
if (a || b || c) {
skipBlock = _skipBlock;
if (getProperty("forceHomeOnIndexing")) {
writeRetract(X, Y);
skipBlock = _skipBlock;
}
// var clamped = axisIsClamped;
// onCommand(COMMAND_UNLOCK_MULTI_AXIS); // handled automatically by the control
skipBlock = _skipBlock;
writeBlock(gMotionModal.format(0), a, b, c, formatComment("ALIGN HEAD"));
/*if (clamped) { // handled automatically by the control
skipBlock = _skipBlock;
onCommand(COMMAND_LOCK_MULTI_AXIS);
}*/
currentMachineABC = new Vector(0, 0, 0);
previousABCPosition = new Vector(0, 0, 0);
setCurrentABC(currentMachineABC);
}
}
// force any axes that move to home on next block
if (_xyzMoved[0]) {
xOutput.reset();
}
if (_xyzMoved[1]) {
yOutput.reset();
}
if (_xyzMoved[2]) {
zOutput.reset();
}
}
}
var isDPRNTopen = false;
function inspectionCreateResultsFileHeader() {
if (isDPRNTopen) {
if (!getProperty("singleResultsFile")) {
writeln("DPRNT[END]");
writeBlock("PCLOS");
isDPRNTopen = false;
}
}
if (isProbeOperation() && !printProbeResults()) {
return; // if print results is not desired by probe/ probeWCS
}
if (!isDPRNTopen) {
writeBlock("PCLOS");
writeBlock("POPEN");
// check for existence of none alphanumeric characters but not spaces
var resFile;
if (getProperty("singleResultsFile")) {
resFile = getParameter("job-description") + "-RESULTS";
} else {
resFile = getParameter("operation-comment") + "-RESULTS";
}
resFile = resFile.replace(/:/g, "-");
resFile = resFile.replace(/[^a-zA-Z0-9 -]/g, "");
resFile = resFile.replace(/\s/g, "-");
writeln("DPRNT[START]");
writeln("DPRNT[RESULTSFILE*" + resFile + "]");
if (hasGlobalParameter("document-id")) {
writeln("DPRNT[DOCUMENTID*" + getGlobalParameter("document-id") + "]");
}
if (hasGlobalParameter("model-version")) {
writeln("DPRNT[MODELVERSION*" + getGlobalParameter("model-version") + "]");
}
}
if (isProbeOperation() && printProbeResults()) {
isDPRNTopen = true;
}
}
function getPointNumber() {
if (typeof inspectionWriteVariables == "function") {
return (inspectionVariables.pointNumber);
} else {
return ("#172[60]");
}
}
function inspectionWriteCADTransform() {
var cadOrigin = currentSection.getModelOrigin();
var cadWorkPlane = currentSection.getModelPlane().getTransposed();
var cadEuler = cadWorkPlane.getEuler2(EULER_XYZ_S);
writeln(
"DPRNT[G331" +
"*N" + getPointNumber() +
"*A" + abcFormat.format(cadEuler.x) +
"*B" + abcFormat.format(cadEuler.y) +
"*C" + abcFormat.format(cadEuler.z) +
"*X" + xyzFormat.format(-cadOrigin.x) +
"*Y" + xyzFormat.format(-cadOrigin.y) +
"*Z" + xyzFormat.format(-cadOrigin.z) +
"]"
);
}
function inspectionWriteWorkplaneTransform() {
var orientation = (machineConfiguration.isMultiAxisConfiguration() && currentMachineABC != undefined) ? machineConfiguration.getOrientation(currentMachineABC) : currentSection.workPlane;
var abc = orientation.getEuler2(EULER_XYZ_S);
writeln("DPRNT[G330" +
"*N" + getPointNumber() +
"*A" + abcFormat.format(abc.x) +
"*B" + abcFormat.format(abc.y) +
"*C" + abcFormat.format(abc.z) +
"*X0*Y0*Z0*I0*R0]"
);
}
function writeProbingToolpathInformation(cycleDepth) {
writeln("DPRNT[TOOLPATHID*" + getParameter("autodeskcam:operation-id") + "]");
if (isInspectionOperation()) {
writeln("DPRNT[TOOLPATH*" + getParameter("operation-comment") + "]");
} else {
writeln("DPRNT[CYCLEDEPTH*" + xyzFormat.format(cycleDepth) + "]");
}
}
function onClose() {
if (isDPRNTopen) {
writeln("DPRNT[END]");
writeBlock("PCLOS");
isDPRNTopen = false;
if (typeof inspectionProcessSectionEnd == "function") {
inspectionProcessSectionEnd();
}
}
cancelG68Rotation();
writeln("");
optionalSection = false;
onCommand(COMMAND_STOP_SPINDLE);
onCommand(COMMAND_COOLANT_OFF);
cancelWorkPlane();
// retract
forceABC();
writeRetract(Z);
onCommand(COMMAND_LOCK_MULTI_AXIS);
if (!getProperty("forceHomeOnIndexing")) {
writeRetract(Y);
}
if (getProperty("homePositionCenter", false) && hasParameter("part-upper-x") && hasParameter("part-lower-x")) {
var xHome = (getParameter("part-upper-x") + getParameter("part-lower-x")) / 2;
writeBlock(gFormat.format(0), xOutput.format(xHome));
}
onImpliedCommand(COMMAND_END);
onImpliedCommand(COMMAND_STOP_SPINDLE);
writeBlock(mFormat.format(30)); // stop program, spindle stop, coolant off
if (subprograms.length > 0) {
writeln("");
write(subprograms);
}
writeln("");
writeln("%");
}
/*
keywords += (keywords ? " MODEL_IMAGE" : "MODEL_IMAGE");
function onTerminate() {
var outputPath = getOutputPath();
var programFilename = FileSystem.getFilename(outputPath);
var programSize = FileSystem.getFileSize(outputPath);
var postPath = findFile("setup-sheet-excel-2007.cps");
var intermediatePath = getIntermediatePath();
var a = "--property unit " + ((unit == IN) ? "0" : "1"); // use 0 for inch and 1 for mm
if (programName) {
a += " --property programName \"'" + programName + "'\"";
}
if (programComment) {
a += " --property programComment \"'" + programComment + "'\"";
}
a += " --property programFilename \"'" + programFilename + "'\"";
a += " --property programSize \"" + programSize + "\"";
a += " --noeditor --log temp.log \"" + postPath + "\" \"" + intermediatePath + "\" \"" + FileSystem.replaceExtension(outputPath, "xlsx") + "\"";
execute(getPostProcessorPath(), a, false, "");
executeNoWait("excel", "\"" + FileSystem.replaceExtension(outputPath, "xlsx") + "\"", false, "");
}
*/
// >>>>> INCLUDED FROM include_files/parseSpatialProperties.cpi
function parseSpatialProperties() {
for (property in properties) {
if (properties[property].kind && properties[property].kind == "spatial") {
if (properties[property].type != "string") {
error(localize("Spatial unit properties must be defined with a type of \"string\"."));
}
if (properties[property].scope.indexOf("operation") != -1) {
error(localize("Spatial properties with scope \"operation\" are currently not supported."));
}
var text = getProperty(property).toString().toUpperCase();
var unitStr = text.replace(/[^A-Z]/g, "");
var value = text.slice(0, text.length - 2);
if (unitStr != "IN" && unitStr != "MM") {
error(subst(localize("Unsupported unit \"%1\" entered for property \"%2\". Only 'IN' and 'MM' are supported."), unitStr, property));
}
if (value.indexOf(",") != -1) {
error(subst(localize("Invalid decimal separator 'comma' entered for property \"%1\". Only 'point' is supported."), property));
}
properties[property].value = Number(value);
if (isNaN(properties[property].value)) {
error(subst(localize("Invalid numeric value of \"%1\" entered for property \"%2\"."), value, property));
}
setProperty(property, properties[property].value *= (unitStr == "IN" && unit == MM) ? 25.4 :
((unitStr == "MM" && unit == IN) ? 1 / 25.4 : 1)
);
}
}
}
// <<<<< INCLUDED FROM include_files/parseSpatialProperties.cpi
// <<<<< INCLUDED FROM haas/head-head/common/haas head-head.cps
properties.homePositionCenter = {
title : "Home position center",
description: "Enable to center the part along X at the end of program for easy access.",
group : "homePositions",
type : "boolean",
value : false,
scope : "post"
};